Lantronix EDS3000PS Command Reference - Page 70

Restores the default Project Tag.

Get Lantronix EDS3000PS PDF manuals and user guides View all Lantronix EDS3000PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

6: Commands and Levels local port no project tag Sets the local port for consoleflow client. When configured, a total of 16 consecutive ports will be reserved. Restores the default Project Tag. project tag Sets the Project Tag. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. state disable Disables command processing on line. state enable Enables command processing on line. status update interval write Sets the status update interval. Stores the current configuration in permanent memory. link (config-ethernet:eth0) level commands clrscrn Clears the screen. default duplex Restores the default duplex setting, which is auto. default speed Restores the default speed setting, which is auto-negotiate. duplex auto Sets duplex mode to auto. duplex full Sets duplex mode to full. duplex half Sets duplex mode to half. exit Exit back to interface configuration level show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. speed 10 Sets the speed of the Ethernet link to 10 Mbps. speed 100 Sets the speed of the Ethernet link to 100 Mbps. speed auto write Sets the speed of the Ethernet link to auto-negotiate. Stores the current configuration in permanent memory. log (config-diagnostics-log) level commands clrscrn Clears the screen. default max length Restores the factory default maximum Log file size. default output Restores the default log output, which is disable. exit Exits to the next higher level. max length Sets the maximum size in Kbytes for the Log file. output disable Disables log output. output filesystem Enables log to filesystem. output line Enables log to serial line. show Shows the current configuration. show history write Displays the last 20 commands entered during the current CLI session. Stores the current configuration in permanent memory. modem (tunnel-modem:) level commands ( is the number of the line) clrscrn Clears the screen. connect string Sets the CONNECT string used in modem emulation. = connect string. default incoming connection Default disables incoming network connections. default response type Default uses text type responses. display remote ip disable The incoming RING has nothing following it. display remote ip enable The incoming RING is followed by the IP address of the caller. EDS3000 Command Reference 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
6: Commands and Levels
EDS3000 Command Reference
70
local port
<number>
Sets the local port for consoleflow client. When configured, a total of 16
consecutive ports will be reserved.
no project tag
Restores the default Project Tag.
project tag
<text>
Sets the Project Tag.
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
state disable
Disables command processing on line.
state enable
Enables command processing on line.
status update interval
<minutes>
Sets the status update interval.
write
Stores the current configuration in permanent memory.
link (config-ethernet:eth0) level commands
clrscrn
Clears the screen.
default duplex
Restores the default duplex setting, which is auto.
default speed
Restores the default speed setting, which is auto-negotiate.
duplex auto
Sets duplex mode to auto.
duplex full
Sets duplex mode to full.
duplex half
Sets duplex mode to half.
exit
Exit back to interface configuration level
show
Displays the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
speed 10
Sets the speed of the Ethernet link to 10 Mbps.
speed 100
Sets the speed of the Ethernet link to 100 Mbps.
speed auto
Sets the speed of the Ethernet link to auto-negotiate.
write
Stores the current configuration in permanent memory.
log (config-diagnostics-log) level commands
clrscrn
Clears the screen.
default max length
Restores the factory default maximum Log file size.
default output
Restores the default log output, which is disable.
exit
Exits to the next higher level.
max length
<Kbytes>
Sets the maximum size in Kbytes for the Log file.
output disable
Disables log output.
output filesystem
Enables log to filesystem.
output line
<number>
Enables log to serial line.
show
Shows the current configuration.
show history
Displays the last 20 commands entered during the current CLI session.
write
Stores the current configuration in permanent memory.
modem (tunnel-modem:
<line>
) level commands (
<line>
is the number of the line)
clrscrn
Clears the screen.
connect string
<text>
Sets the CONNECT string used in modem emulation. <string> = connect
string.
default incoming connection Default disables incoming network connections.
default response type
Default uses text type responses.
display remote ip disable
The incoming RING has nothing following it.
display remote ip enable
The incoming RING is followed by the IP address of the caller.