Lenovo NetVista A22 User guide for NetVista 2254, 2256, 2257, 6336, 6337, 6339 - Page 33

Installing memory, Use 32 MB, 64 MB, 128 MB, or 256 MB DIMMs in any combination

Get Lenovo NetVista A22 PDF manuals and user guides View all Lenovo NetVista A22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

See the following illustration for the location of parts on the system board. 1 Fan connector 11 2 Microprocessor 12 3 DIMM 1 13 4 DIMM 2 14 5 Power connector 15 6 Power connector 16 7 Hard disk LED connector 17 8 Power LED connector 18 9 Diskette connector 19 10 Secondary IDE connector Primary IDE connector Front USB connector Virtual Clear CMOS/BIOS recovery jumper (JP14) Battery PCI slot PCI slot PCI slot CD-ROM audio connector Front panel connector Installing memory Your computer has two connectors for installing dual in-line memory modules (DIMMs) that provide up to a maximum of 512 MB of system memory. Installing DIMMs When installing DIMMs, the following rules apply: v Fill each system memory connector sequentially, starting at DIMM 1 v Use 3.3 V, synchronous, 168-pin, unbuffered, 133 MHz, nonparity, synchronous dynamic random access memory (SDRAM) v Use 32 MB, 64 MB, 128 MB, or 256 MB DIMMs in any combination v DIMM heights of 38.1 mm (1.5 inches) To install a DIMM: 1. Remove the cover. See "Removing the cover" on page 19. Chapter 3. Installing internal options - small desktop model 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
See the following illustration for the location of parts on the system board.
±1²
Fan connector
±11²
Primary IDE connector
±2²
Microprocessor
±12²
Front USB connector
±3²
DIMM 1
±13²
Virtual Clear CMOS/BIOS recovery jumper (JP14)
±4²
DIMM 2
±14²
Battery
±5²
Power connector
±15²
PCI slot
±6²
Power connector
±16²
PCI slot
±7²
Hard disk LED connector
±17²
PCI slot
±8²
Power LED connector
±18²
CD-ROM audio connector
±9²
Diskette connector
±19²
Front panel connector
±10²
Secondary IDE connector
Installing memory
Your computer has two connectors for installing dual in-line memory modules
(DIMMs) that provide up to a maximum of 512 MB of system memory.
Installing DIMMs
When installing DIMMs, the following rules apply:
v
Fill each system memory connector sequentially, starting at DIMM 1
v
Use 3.3 V, synchronous, 168-pin, unbuffered, 133 MHz, nonparity, synchronous
dynamic random access memory (SDRAM)
v
Use 32 MB, 64 MB, 128 MB, or 256 MB DIMMs in any combination
v
DIMM heights of 38.1 mm (1.5 inches)
To install a DIMM:
1.
Remove the cover. See
“
Removing the cover
”
on page 19.
Chapter 3. Installing internal options
—
small desktop model
21