Motorola 49901 Software Release Notes - Page 34

Software Improvements, Quad FXO ports Booting to the Correct State

Get Motorola 49901 - Vanguard 340 Router PDF manuals and user guides
UPC - 786523499018
View all Motorola 49901 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Software Improvements Part No. T0001-42, Rev C October, 2002 Page 34 of 103 Software Improvements Introduction Corrected Limitations This section describes specific improvements to the Applications Ware software. It includes: • Corrected limitations • Customer-initiated Change Requests Central Voice Switching Table - All Products Central Voice Switching Table lookups indicate the wrong entry if a blank entry exists. (DRCaa22754) This is fixed Vanguard 7300 Series, DSP Configuration Crash A DSP failure occurred when using a certain configuration. The failure occurred when using a certain T1/E1 card, DSPM daughtercard and when voice calls were disconnected. (DRCaa23026) This is fixed. Quad FXO ports Booting to the Correct State Intermittently Quad FXO ports may not boot to the correct state during a node boot (cold or warm). This condition can be observed within page three of the ports Detailed Port Statistics. (DRCaa23122) Figure 9. Detailed Port Statistics - Correct State Figure 9 shows that the port statistics page reports the following conditions as the current port state: • Rx State = 1000 and Voice State = IDLE_UNCON - This means that the port has booted to the correct state.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Part No. T0001-42, Rev C
October, 2002
Software Improvements
Page 34 of 103
Software Improvements
Introduction
This section describes specific improvements to the Applications Ware software. It
includes:
•
Corrected limitations
•
Customer-initiated Change Requests
Corrected
Limitations
Central Voice Switching Table - All Products
Central Voice Switching Table lookups indicate the wrong entry if a blank entry
exists. (DRCaa22754)
This is fixed
Vanguard 7300 Series, DSP Configuration Crash
A DSP failure occurred when using a certain configuration. The failure occurred
when using a certain T1/E1 card, DSPM daughtercard and when voice calls were
disconnected. (DRCaa23026)
This is fixed
.
Quad FXO ports Booting to the Correct State
Intermittently Quad FXO ports may not boot to the correct state during a node boot
(cold or warm). This condition can be observed within page three of the ports
Detailed Port Statistics. (DRCaa23122)
Figure 9. Detailed Port Statistics - Correct State
Figure 9 shows that the port statistics page reports the following conditions as the
current port state:
•
Rx State = 1000 and Voice State = IDLE_UNCON - This means that the port
has booted to the correct state.