Motorola 49901 Software Release Notes - Page 58

Virtual Links between two OSPF Area Border Routers Fail - Vanguard

Get Motorola 49901 - Vanguard 340 Router PDF manuals and user guides
UPC - 786523499018
View all Motorola 49901 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Known Software Limitations Part No. T0001-42, Rev C October, 2002 Page 58 of 103 cent). A number of factors effect the number of buffers used, including the number of SVCs used and the rate of data transfer through the node. (DRFaa16497) Workaround: Reduce number of connections (SVCs) or traffic through node in order to reduce number of buffers used. Vanguard 7300 Series T3 ATM PMC Card Only Supported in Slot 1 of the Carrier Expansion Card Due to the design of the T3 ATM Rear Transition Module, only the top slot of the Carrier Expansion Card supports the T3 ATM PMC. (DRFaa16824) Workaround: For information on installing the T3 ATM PMC, refer to the 7300 Series Installation Manual (Part Number T0185). V.34 Modem Calls not Connecting - Vanguard 6560, 6400 and 7300 Series V.34 Modem calls do not consistently connect over Autocall and Transparent connection types. (DRCaa22907) Workaround: At present, there is no workaround. Virtual Links between two OSPF Area Border Routers Fail - Vanguard 7300 Series Virtual links between two OSPF Area Border Routers do not work properly. (DRFaa17076) Workaround: At present, there is no workaround. Voice Server Card Removal - Vanguard 7300 Series If the voice server card is removed from the T1 card and there is a voice configuration in the node, the node will not boot. (DRCaa22978) Workaround: Delete the voice configuration or default the node before removing the voice server card. SNABSC HPAD and TPAD Entries - Vanguard 6455, 7300 Series The Destination Control Unit Address and Destination Device Address parameters in the SNABSC entry in HPAD must match one of the following set of parameters of BSC3270 TPAD device table, for the device it is connecting to: (DRCaa22909) 1) BSC Control Unit Address and BSC Device Address. 2) Destination Control Unit Address and Destination Device Address. When placing the call from HPAD, the Destination Control Unit Address and Destination Device Address must match the BSC3270 device table parameters: BSC Control Unit Address and BSC Device Address. When placing the call from TPAD, the Destination Control Unit Address and Destination Device Address must also match the BSC3270 device table parameters: Destination Control Unit Address and Destination Device Address.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
Part No. T0001-42, Rev C
October, 2002
Known Software Limitations
Page 58 of 103
cent). A number of factors effect the number of buffers used, including the number
of SVCs used and the rate of data transfer through the node. (DRFaa16497)
Workaround:
Reduce number of connections (SVCs) or traffic through node in order
to reduce number of buffers used.
Vanguard 7300 Series T3 ATM PMC Card Only Supported in
Slot 1 of the Carrier Expansion Card
Due to the design of the T3 ATM Rear Transition Module, only the top slot of the
Carrier Expansion Card supports the T3 ATM PMC. (DRFaa16824)
Workaround:
For information on installing the T3 ATM PMC, refer to the
7300
Series Installation Manual
(Part Number T0185).
V.34 Modem Calls not Connecting - Vanguard 6560, 6400 and
7300 Series
V.34 Modem calls do not consistently connect over Autocall and Transparent
connection types. (DRCaa22907)
Workaround:
At present, there is no workaround.
Virtual Links between two OSPF Area Border Routers Fail - Vanguard
7300 Series
Virtual links between two OSPF Area Border Routers do not work properly.
(DRFaa17076)
Workaround:
At present, there is no workaround.
Voice Server Card Removal - Vanguard 7300 Series
If the voice server card is removed from the T1 card and there is a voice
configuration in the node, the node will not boot. (DRCaa22978)
Workaround:
Delete the voice configuration or default the node before removing the
voice server card.
SNABSC HPAD and TPAD Entries - Vanguard 6455, 7300 Series
The Destination Control Unit Address and Destination Device Address parameters in
the SNABSC entry in HPAD must match one of the following set of parameters of
BSC3270 TPAD device table, for the device it is connecting to: (DRCaa22909)
1) BSC Control Unit Address and BSC Device Address.
2) Destination Control Unit Address and Destination Device Address.
When placing the call from HPAD, the Destination Control Unit Address and
Destination Device Address must match the BSC3270 device table parameters: BSC
Control Unit Address and BSC Device Address. When placing the call from TPAD,
the Destination Control Unit Address and Destination Device Address must also
match the BSC3270 device table parameters: Destination Control Unit Address and
Destination Device Address.