Netgear RND4000 RND4000 User Manual - Page 100

Warning, for 30 seconds while powering on the device.

Get Netgear RND4000 - ReadyNAS NV+ NAS Server PDF manuals and user guides
UPC - 606449053272
View all Netgear RND4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

NETGEAR ReadyNAS User Guide The following figure illustrates the default configuration with redundancy in your ReadyNAS NV+. Figure 3-8 You can switch between the X-RAID Expandable Volume mode and the RAID 0/1/5 Flexible Volume mode only if you want to change the default configuration. It is not necessary to perform this procedure every time you boot up the system. The device remains in the selected mode until explicitly changed. Warning: Performing a Factory Default will erase all your data on the hard disks. To reconfigure your RAID setup: 1. Power off the device. 2. Use a paper clip or push pin to press the System Reset switch. Press the System Reset switch for 30 seconds while powering on the device. The four LEDs will flash for approximately 30 seconds. 3. When the LEDS are on, but not flashing, release the reset switch. 3-8 Maintenance and Administration v1.0, October 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
NETGEAR ReadyNAS User Guide
3-8
Maintenance and Administration
v1.0, October 2007
The following figure illustrates the default configuration with redundancy in your ReadyNAS
NV+.
You can switch between the X-RAID Expandable Volume mode and the RAID 0/1/5 Flexible
Volume mode only if you want to change the default configuration. It is not necessary to perform
this procedure every time you boot up the system. The device remains in the selected mode until
explicitly changed.
To reconfigure your RAID setup:
1.
Power off the device.
2.
Use a paper clip or push pin to press the System Reset switch. Press the System Reset switch
for 30 seconds while powering on the device.
The four LEDs will flash for approximately 30 seconds.
3.
When the LEDS are on, but not flashing, release the reset switch.
Figure 3-8
Warning:
Performing a Factory Default will erase all your data on the hard disks.