Home » Netgear Manuals » Wireless » Netgear WG602 » Manual Viewer

Netgear WG602 WG602v3 User Manual - Page 19

WG602v3 Wireless Access Point Front Panel, Table 1-1., Front Panel LED Description - wireless is not blinking

UPC - 606449030730

Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual WG602v3 Wireless Access Point Front Panel The wireless access point provides three status LEDs. Power Ethernet Wireless Figure 1-1 The following table explains the LED indicators. Table 1-1. Front Panel LED Description LED Power Off On Ethernet Off Green On Green Blink Amber On Amber Blink Wireless Off Green On Green Blink DESCRIPTION Power Indicator No power. If this LED does not come on with the power adapter and cord correctly installed, see Chapter 5, "Troubleshooting." Power is on. Indicates no Ethernet link detected. 100 Mbps Fast Ethernet link detected, no activity. Indicates data traffic on the 100Mbps Ethernet LAN. 10 Mbps Ethernet link detected, no activity. Indicates data traffic on the 10Mbps Ethernet LAN. Indicates no wireless link detected. Wireless link enabled, no activity. Wireless link activity. Introduction 1-5 v1.0, August 2006

Section	Page
NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual	1
Contents	7
About This Manual	11
Audience, Scope, Conventions, and Formats	11
How to Use This Manual	12
How to Print this Manual	12
Chapter 1 Introduction	15
About the NETGEAR WG602v3 54 Mbps Wireless Access Point	15
Support for Standards	15
Key Features	16
802.11b/g Standards-based Wireless Networking	17
Autosensing Ethernet Connections with Auto Uplink	17
Wireless Multimedia (WMM) Support	17
Compatible and Related NETGEAR Products	17
What’s In the Box?	18
Hardware Description	18
WG602v3 Wireless Access Point Front Panel	19
WG602v3 Wireless Access Point Rear Panel	20
Chapter 2 Installation and Configuration	21
Placement and Range Guidelines	21
System Requirements	22
Basic Setup and Installation	22
Installing the WG602v3	23
Selecting Basic IP Settings Options	23
Verifying Wireless Connectivity	28
Deploying the Wireless AP	28
Logging Into the WG602v3	29
IP Address Login	29
NetBIOS Name Login	30
Wireless Security Options	32
Configuring Wireless Security	33
Wireless Settings Information Form	35
Configuring WEP Wireless Security	36
Configuring WPA-PSK Wireless Security	37
Configuring WPA2-PSK Wireless Security	38
Configuring WPA-PSK/WPA2-PSK Wireless Security	38
Restricting Wireless Access by MAC Address	39
Chapter 3 Management	43
Viewing General Information	43
Viewing a List of Attached Devices	44
Upgrading the Wireless Access Point Software	45
Rebooting and Resetting Factory Defaults	46
Rebooting the Wireless AP	47
Restoring Factory Default Settings	47
Using the Reset Button to Reboot or Restore Factory Defaults	47
Changing the Administrator Password	48
Chapter 4 Advanced Configuration	49
Configuring Access Point Modes	49
Configuring a WG602v3 as a Point-to-Point Bridge	49
Configuring Wireless Multi-Point Bridging	52
Configuring Repeater with Wireless Client Association	55
Client Mode Configuration	57
Advanced Wireless Settings	61
Chapter 5 Troubleshooting	63
Troubleshooting	63
No lights are lit on the access point.	63
The Ethernet LAN light is not lit.	63
The Wireless LAN activity light is not lit.	64
I cannot configure the wireless access point from a browser.	64
I cannot access the Internet or the LAN with a wireless capable computer.	64
When I enter a URL or IP address I get a timeout error.	65
Using the Reset Button to Restore Factory Default Settings	65
Appendix A Default Configuration and Technical Specifications	67
Default Configuration Settings	67
Technical Specifications	68
Appendix B Related Documents	71