Netgear WG602 WG602v3 User Manual - Page 40

Setup, Access Control, MAC Address, Apply - repeater setup

Get Netgear WG602 - 54 Mbps Wireless Access Point PDF manuals and user guides
UPC - 606449030730
View all Netgear WG602 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual To restrict access based on a MAC address: 1. From under the Setup menu in the left-hand panel, click Access Control. The Access Control screen will display. 2. Check the Access Control radio button for the type of access control you want to enable. Access Control is disabled by default: • Disable • Allow • Block Figure 2-16 If you selected Allow, then all addresses will be blocked except those added to the MAC Address list; conversely, if you selected Block, then all addresses are accepted except those added to the MAC Address List. 3. Enter the MAC Address for the device you want to manage in the MAC address field. (You can usually find the MAC address printed on the bottom of the device.) Tip: You can copy and paste the MAC addresses from the WG602v3's Station List table into the MAC Address box. First, configure each wireless PC to obtain a wireless link to the WG602v3 so that the PC appears in the Station List table. 4. Click Add to add each wireless device to the access list. Repeat these steps for each additional device to be added. 5. Click Apply to save your wireless access control list settings. 2-20 v1.0, August 2006 Installation and Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual
2-20
Installation and Configuration
v1.0, August 2006
To restrict access based on a MAC address:
1.
From under the
Setup
menu in the left-hand panel, click
Access Control
. The
Access Control
screen will display.
2.
Check the
Access Control
radio button for the type of access control you want to enable.
Access Control is disabled by default:
•
Disable
•
Allow
•
Block
If you selected Allow, then all addresses will be blocked except those added to the MAC
Address list; conversely, if you selected Block, then all addresses are accepted except those
added to the MAC Address List.
3.
Enter the
MAC Address
for the device you want to manage in the MAC address field. (You
can usually find the MAC address printed on the bottom of the device.)
4.
Click
Add
to add each wireless device to the access list. Repeat these steps for each additional
device to be added.
5.
Click
Apply
to save your wireless access control list settings.
Figure 2-16
Tip:
You can copy and paste the MAC addresses from the WG602v3’s Station List
table into the MAC Address box. First, configure each wireless PC to obtain a
wireless link to the WG602v3 so that the PC appears in the Station List table.