Netgear WG602 WG602v3 User Manual - Page 44

Viewing a List of Attached Devices, Table 3-1., General Information Fields - wg602v3 firmware

Get Netgear WG602 - 54 Mbps Wireless Access Point PDF manuals and user guides
UPC - 606449030730
View all Netgear WG602 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual This screen displays the following parameters: Table 3-1. General Information Fields Field Description Access Point Information Access Point Mode Shows the current operating mode of the device: AP, Bridge, Repeater or Client. Access Point Name The default name can be changed if desired. MAC Address Displays the Media Access Control address (MAC Addresses) of the wireless access point's Ethernet port. Region Displays the country or region for which the wireless access point is licensed for use. It may not be legal to operate this wireless access point in a region other than one of those identified in this field. Firmware Version The version of the firmware currently installed. Current IP Settings - These parameters apply to the Local WG602v3 wireless access point. IP Address The IP address of the wireless access point. Subnet Mask The subnet mask for the wireless access point. Default Gateway The default gateway for the wireless access point. DHCP Client Enabled by default. Enabled (DHCP client) indicates that the current IP address was obtained from a DHCP server on your network. Wireless Settings - These parameters apply to the target remote WG602v3, VPN gateway, or VPN client. Wireless Network Name (SSID) Displays the wireless network name (SSID) being used by the wireless port of the wireless access point. The default is NETGEAR. Associated AP (Client mode only) The MAC address of a remote AP or peer that this wireless access point is connected to. Channel Identifies the channel the wireless port is using. Encryption Type The current encryption setting. Access Control Restricts wireless access by MAC address. Disabled by default. Viewing a List of Attached Devices The Station List table contains a list of all devices associated with this wireless access point in the wireless network defined by their Wireless Network Name (SSID). The feature is not available when in Client Mode. 3-2 Management v1.0, August 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual
3-2
Management
v1.0, August 2006
This screen displays the following parameters:
Viewing a List of Attached Devices
The Station List table contains a list of all devices associated with this wireless access point in the
wireless network defined by their Wireless Network Name (SSID). The feature is not available
when in Client Mode.
Table 3-1.
General Information Fields
Field
Description
Access Point Information
Access Point Mode
Shows the current operating mode of the device: AP, Bridge,
Repeater or Client.
Access Point Name
The default name can be changed if desired.
MAC Address
Displays the Media Access Control address (MAC Addresses) of the
wireless access point’s Ethernet port.
Region
Displays the country or region for which the wireless access point is
licensed for use. It may not be legal to operate this wireless access
point in a region other than one of those identified in this field.
Firmware Version
The version of the firmware currently installed.
Current IP Settings –
These parameters apply to the Local WG602v3 wireless access point
.
IP Address
The IP address of the wireless access point.
Subnet Mask
The subnet mask for the wireless access point.
Default Gateway
The default gateway for the wireless access point.
DHCP Client
Enabled by default. Enabled (DHCP client) indicates that the current
IP address was obtained from a DHCP server on your network.
Wireless Settings –
These parameters apply to the target remote WG602v3, VPN gateway, or VPN client.
Wireless Network Name (SSID)
Displays the wireless network name (SSID) being used by the
wireless port of the wireless access point. The default is NETGEAR.
Associated AP (Client mode
only)
The MAC address of a remote AP or peer that this wireless access
point is connected to.
Channel
Identifies the channel the wireless port is using.
Encryption Type
The current encryption setting.
Access Control
Restricts wireless access by MAC address. Disabled by default.