Oki MC770 MC770/780 User Guide - Basic - Page 63

Placing the originals on the RADF, Lower the Original Cover or RADF slowly.

Get Oki MC770 PDF manuals and user guides View all Oki MC770 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

• When an original of LT/A4 size is placed in the direction shown in the lower figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position B in the figure. • The pre-entered sender information shows what is registered in the Terminal ID.  Advanced Guide 3 Lower the Original Cover or RADF slowly.  Placing the original(s) on the RADF This section describes how to set the original(s) on the RADF (Reversing Automatic Document Feeder). When the originals are placed on the RADF, the uppermost page is the first to be scanned and sent. SENDING/RECEIVING A FAX A B 1 • When scanning the duplex original with the RADF, do not put your hand on the RADF. Paper may damage the hand. • When scanning the duplex original with the RADF, do not put an object on the RADF. This could cause a paper misfeed. 1 After aligning the originals, place them with their face up and slide the guides to rest against the edges of the originals. • When an original of any size other than LT/A4 is placed 2 in the direction shown in the upper figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position A in the figure. • When an original of LT/A4 size is placed in the direction shown in the lower figure, transmission to a recipient is carried out so that the pre-entered sender information is printed in position B in the figure. • The pre-entered sender information shows what is 3 registered in the Terminal ID.  Advanced Guide Sending different width originals To set different width originals, adjust the side guides to the widest original size, and then align the original against the front side. Available combinations of the original size are as follows. • A/B format: A4, B5, FOLIO • North American format: LT, LG 4 • Regardless of their sizes, originals are acceptable up to 100 sheets (35 to 80 g/m2 (9.3 to 20 lb.)) or 16 mm (0.62") in height. • 2-sided originals can be set and sent.  Advanced Guide 5 Memo • To send different width originals, you need to enable "DIFFERENT WIDTH" as a transmission condition.  P.64 "Setting the transmission conditions" 6 - 63 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
SENDING/RECEIVING A FAX
- 63 -
1
2
3
4
5
6
•
When an original of LT/A4 size is placed in the direction
shown in the lower figure, transmission to a recipient is
carried out so that the pre-entered sender information
is printed in position B in the figure.
•
The pre-entered sender information shows what is
registered in the Terminal ID.
Advanced Guide
3
Lower the Original Cover or RADF slowly.
Placing the original(s) on the RADF
This section describes how to set the original(s) on the RADF
(Reversing Automatic Document Feeder). When the originals
are placed on the RADF, the uppermost page is the first to be
scanned and sent.
•
When scanning the duplex original with the RADF, do
not put your hand on the RADF. Paper may damage the
hand.
•
When scanning the duplex original with the RADF, do
not put an object on the RADF. This could cause a paper
misfeed.
1
After aligning the originals, place them with
their face up and slide the guides to rest
against the edges of the originals.
•
Regardless of their sizes, originals are acceptable up
to 100 sheets (35 to 80 g/m
2
(9.3 to 20 lb.)) or 16 mm
(0.62") in height.
•
2-sided originals can be set and sent.
Advanced Guide
•
When an original of any size other than LT/A4 is placed
in the direction shown in the upper figure, transmission
to a recipient is carried out so that the pre-entered
sender information is printed in position A in the figure.
•
When an original of LT/A4 size is placed in the
direction shown in the lower figure, transmission to a
recipient is carried out so that the pre-entered sender
information is printed in position B in the figure.
•
The pre-entered sender information shows what is
registered in the Terminal ID.
Advanced Guide
Sending different width originals
To set different width originals, adjust the side guides to the
widest original size, and then align the original against the front
side. Available combinations of the original size are as follows.
•
A/B format: A4, B5, FOLIO
•
North American format: LT, LG
Memo
•
To send different width originals, you need to enable
“DIFFERENT WIDTH” as a transmission condition.
P.64 "Setting the transmission conditions"
A
B