Oki OKIPOS 407II ParallelBlack Users Guide - Page 40

Auto Cutter Specifications

Get Oki OKIPOS 407II ParallelBlack PDF manuals and user guides View all Oki OKIPOS 407II ParallelBlack manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

10-2. Auto Cutter Specifications (1) Cutting frequency (2) Thickness of paper Max. 20 cuts per minute 0.065 ~ 0.15 mm 10-3. Interface RS-232C serial interface/Two-way parallel interface (IEEE1284)/USB interface/Ethernet interface/Wireless LAN Interface 10-4. Electrical Characteristics (1) Input Voltage DC 24 V±10% (2) Current Consumption (DC 24 V at room temperature) Standby: Approx. 0.15 A ASCII printing: Approx. average 1.8 A (Approx. 17.5% printing rate) 100% print duty: Approx. peak 11.9 A (Solid printing): Approx. average 5.0 A (Continuous solid printing should be 10 seconds or less.) (3) Power Connector Pin No. 1 2 3 Shell Function Drive power (24 V) Signal GND N.C. Frame ground Note: • When using a printer power supply other than the optional AC adaptor (PS60A-24A), be sure that the following cautions are observed. • Use a power supply of DC 24 V ±10% and more than 2.0 A (5.0 A Load 10 sec. Min) with LPS output approved by IEC60950. • Be careful about installing the printer in an area where there is noise. Take the appropriate measures to protect against electrostatic AC line noise, etc. - 36 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
– ³6 –
10-2. Auto Cutter Specifications
(±) Cutting frequency
Max. ²0 cuts per minute
(²) Thickness of paper
0.06µ ~ 0.±µ mm
10-3. Interface
RS-²³²C serial interface/Two-way parallel interface (IEEE±²·´)/USB interface/Ethernet in-
terface/Wireless LAN Interface
10-4. Electrical Characteristics
(±) Input Voltage
DC ²´ V¹±0%
(²) Current Consumption (DC ²´ V at room temperature)
Standby:
Approx. 0.±µ A
ASCII printing:
Approx. average ±.· A
(Approx. ±¶.µ% printing rate)
±00% print duty:
Approx. peak ±±.¸ A
(Solid printing):
Approx. average µ.0 A
(Continuous solid printing should be ±0 seconds or less.)
(³) Power Connector
Pin No.
Function
±
Drive power (²´ V)
²
Signal GND
³
N.C.
Shell
Frame ground
Note:
• When using a printer power supply other than the optional AC adaptor (PS60A-²´A),
be sure that the following cautions are observed.
•
Use a power supply of DC ²´ V ¹±0% and more than ².0 A (µ.0 A Load ±0 sec. Min)
with LPS output approved by IEC60¸µ0.
•
Be careful about installing the printer in an area where there is noise. Take the appropri-
ate measures to protect against electrostatic AC line noise, etc.
<Viewed from Connector Surface>