Olympus E-100RS E-100RS Instructions (English) - Page 108

How to use the flash

Page 108 highlights

How to use the flash 2 1 Slide (flash switch) to pop up the flash. ● The flash may not fire even when the flash is up. 3, 4 2 Press (flash mode button) until the desired flash mode appears on the control panel (see below). ● Auto-flash (no display) [ Red-eye reduction flash ( ) [ Fill-in flash ( ). 1 3 Press the Shutter button halfway down. Flash stand-by/charge mark 6 ● When lights on the display, the flash is ready to fire. P F2.8 1/30 0.0 ● If is blinking, the flash is charging. In this case, release the Shutter button and wait until the flash mark lights steadily before taking the picture. [SM] ● Pay attention to the "Notes" for each mode (p.106/107). Control panel 4 Press the Shutter button all the way down. Flash mode Note: ● The flash may not give you the results you want in the Macro mode, especially with wide-angle shooting. Check your results on the Monitor. If a conversion lens is attached to the lens, it may reduce the output of the flash. ● Unless OFF is selected in All Reset, the setting will be canceled and reset to Auto-Flash when the power is turned off (p.148). 108

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220

6
108
1
Slide
(flash switch) to pop up
the flash.
The flash may not fire even when
the flash is up.
2
Press
(flash mode button) until
the desired flash mode appears on
the control panel (see below).
Auto-flash (no display)
[
Red-eye
reduction flash (
)
[
Fill-in
flash (
).
3
Press the Shutter button halfway
down.
When
lights on the display, the
flash is ready to fire.
If
is blinking, the flash is
charging. In this case, release the
Shutter button and wait until the
flash mark lights steadily before
taking the picture.
Pay attention to the “Notes” for
each mode (p.106/107).
4
Press the Shutter button all the
way down.
How to use the flash
3, 4
2
1
The flash may not give you the results you want in the Macro mode,
especially with wide-angle shooting. Check your results on the Monitor. If a
conversion lens is attached to the lens, it may reduce the output of the
flash.
Unless OFF is selected in All Reset, the setting will be canceled and reset
to Auto-Flash when the power is turned off (p.148).
Note:
Flash stand-by/charge mark
P F2.8 1/30 0.0
[
SM
]
Control panel
Flash mode