Onkyo HT-S7800 Owners Manual - English - Page 12

Step6: Power On & Initial Setup, > Before start, > Hookup, > Playback, > Part Names

Get Onkyo HT-S7800 PDF manuals and user guides View all Onkyo HT-S7800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

> Before start > Hookup > Setup > Playback > Part Names Step6: Power On & Initial Setup Initial Setup starts automatically Once all connections are complete, change the TV's input to the input for this unit, inset batteries in the remote controller, and press Í to turn the power on. When you turn the unit on for the first time, Initial Setup is automatically shown on the TV to enable you to make settings required for startup using simple operations following onscreen guidance. These instructions will guide you through some items that you need to check beforehand. Read beforehand so the setup goes smoothly. a b Initial Setup Language Select English Deutsch Français Español Italiano Nederlands Svenska Exit Operation Select the item with the cursors of the remote controller and press ENTER (a). To return to the previous screen, press (b). To redo the Initial Setup If you terminate the procedure on the way or want to change a setting made during Initial Setup, press on the remote controller, select "7. Miscellaneous" - "Initial Setup", and press ENTER. > Advanced Manual Troubleshooting | Appendix 1. AccuEQ Room Calibration Place the supplied speaker setup microphone in the listening position, measure the test tones emitted by the speakers, then the unit automatically sets the optimum volume level for each speaker, the crossover frequencies, and the distance from the listening position. This also enables correction of distortion caused by the acoustic environment of the room. SETUP MIC 0 When putting the speaker setup microphone on a tripod, refer to the illustration when putting it in place. 0 The subwoofer sound may not be detected since it is extremely low frequencies. Set the subwoofer volume to more than halfway. 0 Calibration takes several minutes to be completed. The speakers emit the test tone at high volume during measurement, so be careful of your surroundings. Keep the room as quiet as possible during measurement. If the measurement is interrupted, turn off the household appliances. Setup 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
12
> Before start
> Hookup
> Setup
> Playback
> Part Names
>
Advanced Manual
Troubleshooting | Appendix
Step6: Power On & Initial Setup
Initial Setup starts automatically
Once all connections are complete, change the TV's input
to the input for this unit, inset batteries in the remote
controller, and press
Í
to turn the power on. When you
turn the unit on for the first time, Initial Setup is
automatically shown on the TV to enable you to make
settings required for startup using simple operations
following onscreen guidance.
These instructions will guide you through some items that
you need to check beforehand. Read beforehand so the
setup goes smoothly.
Operation
Select the item with the cursors of the remote controller
and press ENTER (a). To return to the previous screen,
press
(b).
To redo the Initial Setup
If you terminate the procedure on the way or want to
change a setting made during Initial Setup, press
on
the remote controller, select "7. Miscellaneous" – "Initial
Setup", and press ENTER.
1. AccuEQ Room Calibration
Place the supplied speaker setup microphone in the
listening position, measure the test tones emitted by the
speakers, then the unit automatically sets the optimum
volume level for each speaker, the crossover frequencies,
and the distance from the listening position. This also
enables correction of distortion caused by the acoustic
environment of the room.
0
When putting the speaker setup microphone on a tripod,
refer to the illustration when putting it in place.
0
The subwoofer sound may not be detected since it is
extremely low frequencies. Set the subwoofer volume to
more than halfway.
0
Calibration takes several minutes to be completed. The
speakers emit the test tone at high volume during
measurement, so be careful of your surroundings. Keep
the room as quiet as possible during measurement. If
the measurement is interrupted, turn off the household
appliances.
Setup
a
b
English
Deutsch
Français
Español
Italiano
Nederlands
Svenska
Exit
Initial Setup
Language Select
SETUP MIC