Onkyo HT-S7800 Owners Manual - English - Page 48

>>Specifications >>Settings >>Listening Modes >>Playback Function >>Basic Manual Troubleshooting | Appendix Quick Menu You can quickly adjust settings you frequently use, such as tone adjustments, etc. Operation: You can make the settings on the TV screen while playing something. Press Q on the remote controller to display the Quick Menu. Quick Menu Tone Level AccuEQ Other Bass Treble BD/DVD Select the item with the cursor / buttons of the remote controller and press ENTER to confirm your selection. Use the cursors to change the settings. • To return to the previous screen, press . • To exit the settings, press Q. ˙ Tone Bass: Enhance or moderate the bass range of the front speakers. Treble: Enhance or moderate the treble range of the front speakers. • It cannot be set if the listening mode is Pure Audio (European, Australian and Asian models) or Direct. ˙ Level Center: Adjust the speaker level of the center speaker while 24 listening to some sound. Subwoofer: Adjust the speaker level of the subwoofer while listening to some sound. • The adjustment you made will be reset to the previous status when you turn the unit to standby mode. ˙ AccuEQ AccuEQ Room Calibration: Enable or disable the equalizer function that corrects for distortion caused by the acoustic environment of the room. If this is to be enabled, then normally you should select "On (All Ch)", and to disable just the front speakers you should select "On (ex. L/R)". The setting can be separately set to each input selector. Equalizer: Select "Preset 1" to "Preset 3" configured in "2. Speaker" "Equalizer Settings" in the Setup menu. The same sound field setting is applied all ranges when set to "Off". Cinema Filter: Adjust the soundtrack that was processed to enhance its high pitch range, in order to make it suitable for home theater. This function can be used in the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby Surround, Dolby TrueHD, Multichannel, DTS, DTS-ES, DTS 96/24, DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS Neural:X, DTS Express, Neo:6 Cinema, and DSD. • It cannot be set if the listening mode is Pure Audio (European, Australian and Asian models) or Direct. ˙ Other A/V Sync : If the video is behind the audio, you can delay the audio to offset the gap. Different settings can be set for each input selector. • It cannot be set if the listening mode is Pure Audio (European, Australian and Asian models) or Direct. Music Optimizer: Improve the quality of the compressed audio. Playback sound of lossy compressed files such as MP3 will be improved. The setting can be separately set to each input selector. The setting is effective in the signals of 48 kHz or less. The setting is not effective in the bitstream signals. • It cannot be set if the listening mode is Pure Audio (European, Australian and Asian models) or Direct. Late Night: Make small sounds easily heard. It is useful when you need to reduce the volume while watching a movie late night. You can enjoy the effect only when playing Dolby series and DTS series input signals. • The setting cannot be used in the following cases. - If "Loudness Management" is set to "Off" when playing Dolby Digital Plus or Dolby TrueHD - When the input signal is DTS and "Dialog Control" is other than 0 dB Center Spread: Adjust the width of the sound field of the front channel when playing in the Dolby Surround listening mode. To spread the width of the sound field to the left and right, set to "On". To concentrate sound in the center, set to "Off". • Depending on the speaker settings, this becomes "Off". Dialog Control: You can increase the dialog portion of the audio in 1 dB steps up to 6 dB so that you can make dialog easier to hear over background noise. • This cannot be set for content other than DTS:X. • We plan to provide support for the DTS:X audio format through a firmware update for this unit. Center Image is displayed until the update. • The effect may not be selectable with some content. HDMI Out: Allows you to select the HDMI jack to output video signals from "MAIN", "SUB", and "MAIN+SUB".