Optoma UHL55 Optoma UHL55 User Manual - Page 22

Powering off, Shutdown, Enter

Get Optoma UHL55 PDF manuals and user guides View all Optoma UHL55 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

USING THE PROJECTOR Powering off 1. Turn off the projector by pressing the " " button on the projector keypad or the " " button on the remote control. The following message will be displayed: 2. Press the " "/" " button on the projector keypad or the "t"/"u" button on the remote control to select Shutdown. Then pressing the " " button on the projector keypad or the Enter button on the remote control to confirm. 3. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the status LED will flash white. When the status LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the " "/ " " button again to turn on the projector. 4. Disconnect the power adapter from the projector and the AC power cord from the electrical outlet. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure. 22 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
English
22
USING THE PROJECTOR
Powering off
1.
Turn off the projector by pressing the “
” button on the projector keypad or the “
” button on the
remote control.
The following message will be displayed:
2.
Press the “
”/“
” button on the projector keypad or the “
t
”/“
u
” button on the remote control to select
Shutdown
. Then pressing the “
” button on the projector keypad or the
Enter
button on the remote
control to confirm.
3.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the status LED
will flash white. When the status LED turns solid red, this indicates the projector has entered standby
mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and
the projector has entered standby mode. When the projector is in standby mode, simply press the “
”/
“
” button again to turn on the projector.
4.
Disconnect the power adapter from the projector and the AC power cord from the electrical outlet.
Note:
It is not recommended that the projector is turned on immediately, right after a power off procedure.