Panasonic SLPR300 SLPR300 User Guide - Page 22

press the SET button., Repeat steps 5 and 6 to program up to

Get Panasonic SLPR300 - CD RECORDER PDF manuals and user guides View all Panasonic SLPR300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Listening to CDs 6 Select a track number (1-99) using the R (reverse) or F (forward) buttons, and then press the SET button. SET 1. Select the track. 2. Enter the selection. 7 Repeat steps 5 and 6 to program up to a maximum of 32 steps. • If you try to program over 32 steps, "MEMORY FULL" will be shown in the information display, and the programming function ends automatically. • Pressing the s (stop) button ends the programming function. 8 Press the p button to start program play. • During playback, the disc number, track number and play time of the track are shown in the information display. • The numbers of the tracks that have been played are cleared from the music calendar. They are displayed again when programmed play is completed. • Operation stops automatically (and "STOP" is shown in the information display) when all programmed tracks have been played. • If the p (play) button is pressed at a specific step in a program, the programming function will end and playback will start from Step 01, not the step currently shown in the information display. To clear a step (track) from the program To remove a programmed track, while in the CD stop mode, press the R (reverse skip) or F (forward skip) buttons until the track you want to erase is shown in the information display. Press the CANCEL button to erase the track from the program. The step number for each track following the one erased is automatically reduced by one (i.e., steps are renumbered). To erase the entire program, press the CANCEL button until "PG NO PROGRAM" is shown in the information display. To change the contents of the program In the CD stop mode, press the SET button followed by the CANCEL button. Programmed tracks will be erased in the reverse order of when they were entered (starting from the last track programmed). Press the CANCEL button twice to erase one track. Continue erasing in this manner until all of the tracks you wanted to remove are erased. Enter new tracks into the program by following programming steps 5 and 6. To check the contents of the program To check the tracks you have entered into the program, press the s (stop) button, and use the R (reverse skip) or F (forward skip) buttons to review the programmed tracks. The program steps (PG S**) and track numbers will be shown in the information display one at a time as you toggle through the program (S: Step; **: step number). To return to continuous playback In the CD stop mode, repeatedly press the PLAY MODE button on the remote control until the total playing time is shown in the information display. Remote Control PLAY MODE RQT6087

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
RQT6087
Listening to CDs
6
Select a track number (1-99)
using the
R
(reverse) or
F
(forward) buttons, and then
press the SET button.
7
Repeat steps 5 and 6 to program up to a
maximum of 32 steps.
•
If you try to program over 32 steps,
“
MEMORY FULL
”
will be
shown in the information display, and the programming func-
tion ends automatically.
•
Pressing the
s
(stop) button ends the programming function.
8
Press the
p
button to start program play.
•
During playback, the disc number, track number and play time
of the track are shown in the information display.
•
The numbers of the tracks that have been played are cleared
from the music calendar. They are displayed again when pro-
grammed play is completed.
•
Operation stops automatically (and
“
STOP
”
is shown in the
information display) when all programmed tracks have been
played.
•
If the
p
(play) button is pressed at a specific step in a program,
the programming function will end and playback will start from
Step 01, not the step currently shown in the information display.
To clear a step (track) from the program
To remove a programmed track, while in the CD stop mode, press
the
R
(reverse skip) or
F
(forward skip) buttons until the
track you want to erase is shown in the information display. Press
the CANCEL button to erase the track from the program. The step
number for each track following the one erased is automatically
reduced by one (i.e., steps are renumbered). To erase the entire pro-
gram, press the CANCEL button until
“
PG NO PROGRAM
”
is
shown in the information display.
To change the contents of the program
In the CD stop mode, press the SET button followed by the CAN-
CEL button. Programmed tracks will be erased in the reverse order
of when they were entered (starting from the last track pro-
grammed). Press the CANCEL button twice to erase one track.
Continue erasing in this manner until all of the tracks you wanted
to remove are erased. Enter new tracks into the program by follow-
ing programming steps 5 and 6.
To check the contents of the program
To check the tracks you have entered into the program, press the
s
(stop) button, and use the
R
(reverse skip) or
F
(forward
skip) buttons to review the programmed tracks. The program steps
(PG S**) and track numbers will be shown in the information dis-
play one at a time as you toggle through the program (S: Step; **:
step number).
To return to continuous playback
In the CD stop mode, repeatedly press the PLAY MODE button on
the remote control until the total playing time is shown in the infor-
mation display.
SET
1. Select the track.
2. Enter the selection.
PLAY
MODE
Remote Control