Pioneer DRM-1004 Operating Instructions - Page 14

Troubleshooting

Page 14 highlights

TROUBLESHOOTING Incorrect operations are often mistaken for malfunctions. If you think that there is something wrong with this unit or error code *" EDO is displayed (on the mode indicator), check the points below. A symptom which look like a malfunction is observed or error code is displayed often due to improper maintenance, disc defect or incorrect operation. And what seems to be a serious trouble can be recovered by correcting a simple mistake or misunderstanding or simple care of the unit. If the normal operation cannot be recovered or error code does not disappear after checking the following, please consult a PIONEER after-sale servicing agent or your dealer. Symptom Display Causes Remedy The door will not open. • The key switch is not set to the UNLOCK position. • The door open button has not been pressed for more than 4 seconds. • Some discs have not been returned yet. • Set the key switch to the UNLOCK position using the key. • Press and hold the door open button for more than 4 seconds. • Rezero Unit command must be issued. No operation. The power indicator does not light. No operation. The power indicator lights. • The power is not supplied. • Plug the power cord into the power outlet. • The POWER switch is not switched ON. • Press the POWER switch. OP U-L • The door is open. • Close the door. E83 • The disc is projected inside the Changer. • Open the door, unload the magazines and ensure that no disc is projected from them. The disc cannot be exchanged from the control panel. • The key switch is set to the LOCK position. • Set the key switch to the UNLOCK position using the key. The unit cannot be operated from the host computer. • The SCSI cable to the Changer is not connected properly. • The Function switch and SCSI ID of the Changer are not set properly. • Check the connection cable. • Check the Function switch and SCSI ID switches. The disc cannot be set in the drive. • The disc has not been installed in the • Specify an address in which a disc has specified address. been installed. Data is not delivered. • The disc is placed upside down. • The disc is scratched or dirty. • Due is condensed inside the unit. • Check the disc orientation. • Check that the disc is not scratched or dirty, and exchange or clean the disc as required. • Switch the power OFF, leave the door of the unit open for one or two hours, then try again. After taking action according to the remedies above, switch the power of the unit OFF then ON again. If the error code is displayed or the normal operation cannot be recovered still after this, immediately switch the power OFF again and call a PIONEER after-sale servicing agent or your dealer. For the explanation of the error codes, refer to the error code list attached on the back side of the Changer door. Do not use the following types of discs for they may cause malfunction of the unit or damage to the discs: Disc which has a molding flash (projected fin) left on the periphery as shown in the illustration. Disc with its edges are rounded or tapered as shown in the figure. 14 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52

TROUBLESHOOTING
Incorrect
operations
are
often
mistaken
for
malfunctions.
If
you
think
that
there
is
something
wrong
with
this
unit
or
error
code
*"
EDO
is
displayed
(on
the
mode
indicator),
check
the
points
below.
A
symptom
which
look
like
a
malfunction
is
observed
or
error
code
is
displayed
often
due
to
improper
maintenance,
disc
defect
or
incorrect
operation.
And
what
seems
to
be
a
serious
trouble
can
be
recovered
by
correcting
a
simple
mistake
or
misunderstanding
or
simple
care
of
the
unit.
If
the
normal
operation
cannot
be
recovered
or
error
code
does
not
disappear
after
checking
the
following,
please
consult
a
PIONEER
after
-sale
servicing
agent
or
your
dealer.
Symptom
Display
Causes
Remedy
The
door
wil
l
not
open.
The
key
switch
is
not
set
to
the
UNLOCK
position.
Set
the
key
switch
to
the
UNLOCK
position
using
the
key.
The
door
open
button
has
not
been
pressed
for
more
than
4
seconds.
Press
and
hold
the
door
open
button
for
more
than
4
seconds.
Some
discs
have
not
been
returned
yet.
Rezero
Unit
command
must
be
issued.
No
operation.
The
power
is
not
supplied.
Plug
the
power
cord
into
the
power
outlet.
The
power
indicator
does
not
light.
The
POWER
switch
is
not
switched
ON.
Press
the
POWER
switch.
OP
No
operation.
U
-L
The
door
is
open.
Close
the
door.
The
power
indicator
lights.
E83
The
disc
is
projected
inside
the
Changer.
Open
the
door,
unload
the
magazines
and
ensure
that
no
disc
is
projected
from
them.
The
disc
cannot
be
exchanged
from
the
control
panel.
The
key
switch
is
set
to
the
LOCK
position.
Set
the
key
switch
to
the
UNLOCK
position
using
the
key.
The
unit
cannot
be
operated
from
the
host
computer.
The
SCSI
cable
to
the
Changer
is
not
connected
properly.
Check
the
connection
cable.
The
Function
switch
and
SCSI
ID
of
the
Changer
are
not
set
properly.
Check
the
Function
switch
and
SCSI
ID
switches.
The
disc
cannot
be
set
in
the
drive.
The
disc
has
not
been
installed
in
the
specified
address.
Specify
an
address
in
which
a
disc
has
been
installed.
Data
is
not
delivered.
The
disc
is
placed
upside
down.
Check
the
disc
orientation.
The
disc
is
scratched
or
dirty.
Check
that
the
disc
is
not
scratched
or
dirty,
and
exchange
or
clean
the
disc
as
required.
Due
is
condensed
inside
the
unit.
Switch
the
power
OFF,
leave
the
door
of
the
unit
open
for
one
or
two
hours,
then
try
again.
After
taking
action
according
to
the
remedies
above,
switch
the
power
of
the
unit
OFF
then
ON
again.
If
the
error
code
is
displayed
or
the
normal
operation
cannot
be
recovered
still
after
this,
immediately
switch
the
power
OFF
again
and
call
a
PIONEER
after
-sale
servicing
agent
or
your
dealer.
For
the
explanation
of
the
error
codes,
refer
to
the
error
code
list
attached
on
the
back
side
of
the
Changer
door.
Do
not
use
the
fol
lowing
types
of
discs
for
they
may
cause
malfunction
of
the
unit
or
damage
to
the
discs:
Disc
which
has
a
molding
flash
(projected
fin)
left
on
the
periphery
as
shown
in
the
illustration.
Disc
with
its
edges
are
rounded
or
tapered
as
shown
in
the
figure.
14
<DRC1129>
En