Pioneer VSX-55TXi Owner's Manual - Page 66

select YES. Press ENTER. - av receiver

Get Pioneer VSX-55TXi PDF manuals and user guides View all Pioneer VSX-55TXi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Remote Control of Other Components 5 While LEARN continues to flash, point the two remote controls toward each other. Press the button on the other remote control corresponding to the operation you want to program. S0URCE DVD/LD VCR1/ DVR CD DIMMER 1 SETUP TV SYSTEM RECEIVER OFF TV MULTI CONTROL VCR2 VIDEO CD-R/ TAPE1 SAT TUNER INPUT ATT LOUDNESS SPEAKER A/B 2 VIDEO SEL SIGNAL SEL TAPE 2 EFFECT/CH SELL 5 TONE BASS/TREBLE 9 SYSTEM SETUP MENU TUNER EDIT STATUS GUIDE MPX ¶ TUNING - 1 STATION - 4 CHANNEL - TV INPUT TV CONTROL TV VOL TV CH THX ADVANCED CINEMA ACOUSTIC CAL SURROUND 6 0 ENTER DTV ON/OFF 8 BAND 3 DTV MENU CLASS 7 STANDARD ADVANCED CONCERT (DVD-A/SACD) MULTI CH INPUT AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT AXD7290 3 7 TV CONT MULTI OPERATION RECEIVER - +10 + DISC ENTER DIRECT ACCESS DISP MODE REMOTE SETUP 4 8 EXIT RETURN EXTRA MENU TUNING + ¡ STATION + ¢ CHANNEL + INPUT MIDNIGHT VOLUME DIGITAL NR STEREO /DIRECT LISTENING MODE LISTENING CH SELECT MUTE LIGHT Î After the process is complete and the command has been learned, OK will appear in the remote control display. If NG (no good) appears, it means that for some reason the command was not learned. In this case, repeat steps 4 and 5. CONTINUE? appears in the remote's display. If SELECT KEY is flashing go back to step 4. 6 If you want to program in more commands use the  buttons to select YES. Press ENTER. Repeat steps 4 and 5 to teach the remote control of the VSX-55TXi all the commands from the other remote control. Buttons that are able to learn new commands 7 If you want to program in commands for another MULTI CONTROL button use the  buttons to select NO. Press ENTER. 8 Repeat the process from step 2 for all of your components. Start again to program other components in this manner. Memo: • If FULL appears in step 5 it means that there isn't enough capacity to learn this command. If you want to clear other buttons to make room for this one follow the procedure on page 85. • If there isn't enough capacity, an incorrect signal has been sent or, in some cases, the command from another remote control simply cannot be learned, NG (no good) will appear in the display in step 5. • In some NG cases the remotes just need to be moved closer together or farther apart. 9 When you're done use the  buttons to select EXIT. You will return to the REMOTE SETUP menu. 10Use  to select EXIT and press ENTER. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
Remote Control of Other Components
66
5
While LEARN continues to flash, point
the two remote controls toward each
other. Press the button on the other
remote control corresponding to the
operation you want to program.
After the process is complete and the command has
been learned, OK will appear in the remote control dis-
play. If NG (no good) appears, it means that for some rea-
son the command was not learned. In this case, repeat
steps 4 and 5.
CONTINUE? appears in the remote's display. If SELECT
KEY is flashing go back to step 4.
6
If you want to program in more
commands use the

buttons to
select YES. Press ENTER.
Repeat steps 4 and 5 to teach the remote control of the
VSX-55TXi all the commands from the other remote con-
trol.
7
If you want to program in commands
for another MULTI CONTROL button
use the

buttons to select NO.
Press ENTER.
8
Repeat the process from step 2 for all
of your components.
Start again to program other components in this manner.
9
When you're done use the

buttons to select EXIT.
You will return to the REMOTE SETUP menu.
10Use

to select EXIT and press
ENTER.
Memo:
•
If FULL appears in step 5 it means that
there isn't enough capacity to learn this
command. If you want to clear other
buttons to make room for this one follow
the procedure on page 85.
•
If there isn't enough capacity, an incorrect
signal has been sent or, in some cases, the
command from another remote control
simply cannot be learned, NG (no good)
will appear in the display in step 5.
•
In some NG cases the remotes just need to
be moved closer together or farther apart.
Buttons that are able
to learn new
commands
Î
1
2
3
4
5
6
–
+
+
7
8
9
0
–
–
–
1
4
+
+
+
¡
¢
8
3
7