Pioneer VSX-55TXi Owner's Manual - Page 97

Crossover Network

Get Pioneer VSX-55TXi PDF manuals and user guides View all Pioneer VSX-55TXi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Expert System Settings Crossover Network Crossover frequency is the point where the receiver divides the high and low sounds (the frequencies) between the speakers. Certain bass sounds will play back from the subwoofer if you selected it as YES (or PLUS) or from the front speakers if you selected them as LARGE. This setting decides where the cutoff will be between those bass sounds playing back from the speaker selected as above and the bass sounds for the entire soundtrack, which play back from all speakers used. If all speakers are set to LARGE (see page 41) this setup is unnecessary. Follow steps 1-5 on page 96, if necessary, to get to the starting point mentioned here. 1 CROSSOVER NETWORK should be selected, if it isn't use the  buttons to select and press ENTER. 1-3 2 Use the  buttons to select frequency cut off point. Press ENTER. Frequencies below the cut off point will be sent to the subwoofer (or large speakers). For example, choosing 50 Hz sends bass frequencies below 50 Hz to the subwoofer (or large speakers). 3 EXIT should be selected (if it's not use the  buttons to select it). Press ENTER. Next, proceed to FINE CHANNEL LEVEL. If you want to change a setting before proceeding start over from step 1. Memo: The default is 80Hz. 1 2 3 EXPERT 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
Expert System Settings
97
EXPERT
Crossover Network
Crossover frequency is the point where the receiver divides the high and low sounds (the frequencies) between the
speakers. Certain bass sounds will play back from the subwoofer if you selected it as YES (or PLUS) or from the front
speakers if you selected them as LARGE. This setting decides where the cutoff will be between those bass sounds
playing back from the speaker selected as above and the bass sounds for the entire soundtrack, which play back
from all speakers used.
If all speakers are set to LARGE (see page 41) this setup is unnecessary.
Follow steps 1-5 on page 96, if necessary, to get to the
starting point mentioned here.
1
CROSSOVER NETWORK should be
selected, if it isn’t use the

buttons
to select and press ENTER.
2
Use the

buttons to select
frequency cut off point. Press ENTER.
Frequencies below the cut off point will be sent to the
subwoofer (or large speakers). For example, choosing 50
Hz sends bass frequencies below 50 Hz to the subwoofer
(or large speakers).
3
EXIT should be selected (if it's not use
the

buttons to select it). Press
ENTER.
Next, proceed to FINE CHANNEL LEVEL.
If you want to change a setting before proceeding
start over from step 1.
Memo:
The default is 80Hz.
1
2
3
1-3