Ricoh 402054 Operating Instructions - Page 73

Double Feed has, Digit, Endorser, Start

Get Ricoh 402054 - IS 760 PDF manuals and user guides
UPC - 026649020544
View all Ricoh 402054 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Troubleshooting Message Possible Cause Required Action Cannot continue endorsing due to the limit. • The number of figures • The number of the counter has ex- exceeded or dipped ceeded the value set in [Digit:] under from the values set for the [Endorser] tab. Check the num- the endorser counter. ber of the originals and set [Start:], [Step:], and [Digit:]. • The number of the counter has reached -1 when you set [Step:] under the [Endorser] tab to negative value. Check the number of the originals and set [Start:] and [Step:] so the number of the counter ends in higher values than 0. Cannot add any more scanning mode. • Maximum number of • You can add a maximum of 100 the scanning modes is scanning modes. Delete the modes registered. that you do not use. Cannot specify • Maximum number of • You can add a maximum of 100 any more scanning the scanning areas is scanning areas. Delete the areas that area. registered. you do not use. Double Feed has • Double Feed (More • To continue scanning, replace the occurred. Do you want to than 2 sheets of original was fed into the double fed originals to the ADF and Click [Yes]. Scanning restarts after 6 ADF at once) has oc- you click [Yes]. continue scanning? Set the originals curred and was detected. • To finish scanning, click [No]. • The double feeding is likely to occur when the changeover switch is not again and press set correctly to the paper thickness "Yes" to contin- of the originals. When you scan the ue, regular thickness originals -origi- "No" to end. nals thinner than 128g/m2 (242.5bls)- set the switch on the back side (regular paper mode). Cannot rotate the • Exceeded the maxi- original. mum file size for the Lower the resolu- rotate function. tion and scan again. • Lower the resolution or the set the scan area smaller and scan again. Cannot perform Combine in the current resolution. Set the resolution to over ndpi and scan again. • When combining the • Adjust the resolution to the dis- images, the originals played value. will be scanned with the lowest resolution specified for the scan- ner. The resolution displayed on the mes- sage will be the lowest resolution available for the combine func- tion. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Troubleshooting
69
6
Cannot continue
endorsing due to
the limit.
•
The number of figures
exceeded or dipped
from the values set for
the endorser counter.
•
The number of the counter has ex-
ceeded the value set in
[
Digit:
]
under
the
[
Endorser
]
tab. Check the num-
ber of the originals and set
[
Start:
]
,
[
Step:
]
, and
[
Digit:
]
.
•
The number of the counter has
reached -1 when you set
[
Step:
]
un-
der the
[
Endorser
]
tab to negative
value. Check the number of the
originals and set
[
Start:
]
and
[
Step:
]
so the number of the counter ends in
higher values than 0.
Cannot add any
more scanning
mode.
•
Maximum number of
the scanning modes is
registered.
•
You can add a maximum of 100
scanning modes. Delete the modes
that you do not use.
Cannot specify
any more scanning
area.
•
Maximum number of
the scanning areas is
registered.
•
You can add a maximum of 100
scanning areas. Delete the areas that
you do not use.
Double Feed has
occurred.
Do you want to
continue scan-
ning?
Set the originals
again and press
"Yes" to contin-
ue,
"No" to end.
•
Double Feed (More
than 2 sheets of origi-
nal was fed into the
ADF at once) has oc-
curred and was de-
tected.
•
To continue scanning, replace the
double fed originals to the ADF and
Click
[
Yes
]
. Scanning restarts after
you click
[
Yes
]
.
•
To finish scanning, click
[
No
]
.
•
The double feeding is likely to occur
when the changeover switch is not
set correctly to the paper thickness
of the originals. When you scan the
regular thickness originals
—
origi-
nals thinner than 128g/m
2
(242.5bls)
—
set the switch on the
back side (regular paper mode).
Cannot rotate the
original.
Lower the resolu-
tion and scan
again.
•
Exceeded the maxi-
mum file size for the
rotate function.
•
Lower the resolution or the set the
scan area smaller and scan again.
Cannot perform
Combine in the
current resolu-
tion.
Set the resolu-
tion to over
n-
dpi and scan
again.
•
When combining the
images, the originals
will be scanned with
the lowest resolution
specified for the scan-
ner. The resolution
displayed on the mes-
sage will be the lowest
resolution available
for the combine func-
tion.
•
Adjust the resolution to the dis-
played value.
Message
Possible Cause
Required Action