Sharp LC-M3700 LC-M3700 Operation Manual

Sharp LC-M3700 Manual

Get Sharp LC-M3700 PDF manuals and user guides View all Sharp LC-M3700 manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp LC-M3700 manual content summary:

  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 1
    SHARP CORPORATION WIDE LCD MONITOR 03.7.25, 1:24 PM BEDIENUNGSANLEITUNG MANUAL DE MANEJO OPERATION MANUAL MODE D'EMPLOI LC-M3700/LC-M3710 LC-M3700 LC-M3710 WIDE LCD MONITOR BREITBILD-LCD-MONITOR MONITEUR GRAND ÉCRAN À CRISTAUX LIQUIDES MONITOR LCD PANORÁMICO OPERATION MANUAL BEDIENUNGSANLEITUNG
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 2
    LC-M3700 LC-M3710 WIDE LCD MONITOR ENGLISH OPERATION MANUAL NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 3
    the user's authority to operate this equipment. U.S.A. ONLY CAUTION: Use the supplied AC cord as it is. Do not remove the core part from replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 4
    ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product. 1. Read instructions-All operating instructions must be read and understood before the product is operated. 2. Keep this manual in a safe place-These safety
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 5
    operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. For units designed to operate on batteries or another power source, refer to the operating instructions. The LCD panel is
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 6
    37 PC connection 37 Communication conditions 37 Communication procedure 38 RS-232C command table 46 Settings and Adjustments 51 Picture 51 Audio ...53 Power control 53 Setup ...54 Option 57 Detailed explanation 58 Troubleshooting and Specifications 65 Troubleshooting 65 Specifications
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 7
    SHARP's unique ASV* low-reflection BLACK TFT LCD panel provides higher luminance, higher contrast, and a wider viewing angle. This reduces reflection in the monitor when it is placed near a window, and ensures brighter, more vivid image reproduction. With a wide type Digital Input (DVI terminal) VGA/
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 8
    be controlled in various ways from a PC. 37 •• Multiple monitors can be individually controlled by connecting them in a daisy chain. 37 EXTERNAL SPEAKERS CAN BE CONNECTED 18 • Compatible speakers: L/R, 8 ohm, 10W or larger EQUIPPED WITH BUILT-IN MONITOR SPEAKER (MONO) 57 • When activated from the
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 9
    Part Names - Display Numbers within refer to the main page(s) where the topic is explained. Front view Liquid Crystal Display panel Side control panel (See below.) About LC-M3710: » The SHARP logo for the LC-M3710 model is on the vertical base. LC-3700 LC-3710 Side control panel Remote
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 10
    Introduction Rear view Part Names - Display (Continued) Built-in monitor speaker 57 SPEAKER (R) 18 External speaker terminal (right) POWER 30 Main power on/off switch AC Input terminal 19 SPEAKER (L) 18 External speaker terminal (left) INPUT2 (INPUT/ 14 2 1 3 OUTPUT) VIDEO OUTPUT 17
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 11
    Part Names - Remote Control Unit Numbers within refer to the main page(s) where the topic is explained. Remote control unit Signal transmitter STANDBY/ON 30 INPUT 31 RETURN 32 ENLARGE 31 STANDBY/ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE LCD MONITOR VOL 31 MENU 32 Cursor control
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 12
    such cases, change the angle of the lighting or the monitor, or operate the remote control unit closer to the remote control sensor. Cautions regarding batteries Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. » Do not mix old and
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 13
    ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE LCD MONITOR (RRMCGA186WJSA) Pages 11, 30 - 32 » Operation manual × 1 (UBATU0013TAZZ) Page 11 (QACCDA024WJPZ monitor is equipped with a temporary stand when shipped from the factory. Please note this stand is for temporary use only until the monitor
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 14
    INPUT1 audio INPUT 1 1 R - AUDIO - L S-VIDEO VIDEO S-video Video I INPUT1: Terminals are provided for two types of video input signal. 54 Input Select Video S-video Terminal type BNC S terminal Compatible signals NTSC (3.58/4.43), PAL, SECAM (*1) NTSC (3.58/4.43), PAL, SECAM (*1) No matter
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 15
    : Input or output can be selected for INPUT2. (*1) 56 INPUT2 Select This setting cannot be switched when INPUT2 is currently being displayed. Terminal type Compatible signals Video RCA NTSC (3.58/4.43), PAL, SECAM (*2) When this is set to "Output", video signals input from the INPUT1 video
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 16
    Video adjustment options on the menu are the AV type. Compatible input range: 480i/576i, 480p/576p, 1080i (50Hz (*4) /60Hz), 720p (60Hz). (*1) RGB The monitor operates using Video (RGB) and Sync (HD/VD) signals, just like a PC (analog). Supported sync signals are ordinary separate sync (HD/VD) and
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 17
    ) video PC (analog) video I PC: Terminals for two kinds of PC video input signal are available. 54 Input Select Analog Digital Terminal type D-Sub15-pin DVI-D Compatible signals VGA, SVGA, XGA, SXGA and others 68 Appendix 1 In addition to ordinary Separate Sync (HD/VD) signals, the system is
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 18
    OUTPUT RS-232C INPUT RS-232C OUTPUT I The RS-232C INPUT and RS-232C OUTPUT are used to control this monitor with a PC. To connect a single monitor to a PC, connect to the RS-232C INPUT terminal. To connect multiple monitors in a daisy chain for control by PC, use the RS-232C OUTPUT terminal
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 19
    Plus is red and minus is black. The cables are also divided into plus and minus. When connecting the left/right speakers, be sure to connect the plus/minus jacks with the correct cables. » You can output audio from the built-in monitor speaker on the back of the monitor. See "Monitor Speaker Output
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 20
    connector, and insert all the way in. 2. Attach the supplied cable clamp to the AC cord. 3. Align the hole of the cable clamp with the screw hole on the monitor, and fasten the cable clamp screw. 4. Plug the AC cord into the AC power outlet. » Be sure to plug all the way into
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 21
    Connecting Multiple Monitors I Multiple monitors can be connected in a daisy chain using the input/output terminals for video/audio signals. Connection examples for video only Example: 1 2 1 2 1 VIDEO OUTPUT INPUT 1 Video
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 22
    Connection and Installation Connecting Multiple Monitors (Continued) Connection examples for video and audio 56 Use by selecting "INPUT2 Select" and setting INPUT2 to "Output". Example: 1 INPUT 2 (INPUT/ OUTPUT) VIDEO OUTPUT 2 1 INPUT 1 2 1 INPUT 1 (Red: audio right) (White: audio left) (
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 23
    number (see page 56), you can perform input switching, adjustment and status monitoring of individual monitors. "First monitor "Second monitor "PC RS-232C cross cable To COM port To RS-232C INPUT terminal Related topic: 37 PC Operation US 22 RS-232C cross cable To RS-232C OUTPUT terminal
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 24
    is for temporary use only until the monitor is properly mounted. Be sure to use a special-purpose AN-37ST1 table stand or AN-37AG1 wall-mount bracket (both optional). Mounting the table stand (AN-37ST1) (LC-M3700) See the table stand instructions for details. M5 screws 25 mm length (5 screws
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 25
    Mounting Options (Continued) AN-37AG1 Wall-Mount Bracket Installation See the bracket instructions for details. Mounting precautions Special techniques are required to mount this monitor, so be sure to rely on a specialist for mounting work. The customer should never perform any of this work
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 26
    be careful not to pinch your fingers, etc. Installation angle: LC-M3700 (Horizontal mount) 0° to 20° LC-M3710 (Vertical mount) 0° Screws M6 15mm length (4 screws) As the screw hole numbers become larger (5, 10,15, 20), the Wide LCD Monitor will be tipped farther forward. 20˚ 15˚ 10˚ 5˚ Install
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 27
    to LC-M3700 (horizontal mount) M6 30mm length 2. Attach the wall-mount bracket (with the angle set) to the back of the Wide LCD Monitor. the monitor and align the wall-mount screw holes (Marking A: 4 locations) with the holes (4 locations) on the back of the Wide LCD Monitor. GUse the supplied M6
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 28
    Connection and Installation Outside dimensional drawings »With table stand attached 35-25/32 [909] 31-57/64 [810] Mounting Options (Continued) Unit: inch [mm] 3-29/32 3-15/64 [99.5] [82.1] 2-5/16 [58.8] 11-13/32 [290] 4-17/64 [108.4] 18-7/32 [462.8] 37-23/64 [949] 18-43/64 [474.5] 32-11/32
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 29
    Mounting Options (Continued) Outside dimensional drawings »With wall-mount bracket attached 5-3/32 [129.5] 1-3/16 [30] 6-4/3 [171.7782] 8-3/8 [212.9] 5°
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 30
    Bundling Cables I Cables and cords connected to the back of the monitor can be bundled using the supplied cable clamp and cable binders. This will prevent stray or disorganized cables at the back of the monitor. "Rear view Connection and Installation To external devices Cable binder Wrap the
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 31
    . I There are two power supply switches: POWER (main power supply) and STANDBY/ON. Main POWER switch "Rear view "Front view STANDBY/ON indicator "POWER (main) switch PRESS POWER (MAIN) ON THE BACK OF THE MONITOR. » The STANDBY/ON indicator at the lowerright corner of LCD panel lights up green
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 32
    monitor is operated using the remote control unit once main POWER on the back of the monitor has been turned on. STANDBY/ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE LCD MONITOR 56 61 Enlarge WIDE (Screen size selection) Press WIDE to display the "Wide Mode" menu screen. Press WIDE or use '/"
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 33
    ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE LCD MONITOR Buttons used in menu operation MENU Sharpness Advanced Reset [30] 0 [ 0] -30 [ 0] -30 [ 0] -30 [ 0] -30 Power control 1 +40 +30 +30 +30 +10 Power screen is displayed. » Due to the type of signal and its frequency, the items in the menu
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 34
    Items (Continued) Menu screen explanation "Menu screen example (partial) Power control Setup Control Lock Input Select Position Picture Flip Language Input 2 Select ID No. Setting Enlarge Panel Protection Cover Operation guide MENU [Setup···Picture Flip] Set Picture Direction Normal Mirror Upside
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 35
    (H)/(S)/(V) 52 Red/Green/Blue 53 Treble/Bass/Balance 53 Brightness 53 Power Management 54 Lock Item Menu Display/Remote/Buttons/Power/ RS-232C 54 PIN/PIN Clear 54 Start Now/When Connected 55 H-Pos./V-Pos./Clock/Phase 57 Wide Mode/DNR/Quick Shoot/ Monitor Speaker Output » Due to the type of signal
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 36
    on page 71. Picture Audio Power control Setup Option 51 Contrast/Black Level/Color/Tint/ Sharpness/ 51 Advanced C.M.S. (H)/(S)/(V) / Menu Display/Remote/Buttons/Power/ RS-232C 54 PIN/PIN Clear 55 H-Pos./V-Pos. 57 Wide Mode/Color System/ DNR/Quick Shoot/ Monitor Speaker Output NOTE: »"INPUT2
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 37
    , German, French or Spanish. STANDBY/ON INPUT RETURN VOL MENU ENTER ENLARGE WIDE LCD MONITOR 1 1 Press MENU to display the menu screen. 2 Press or to select "Setup". MENU [Setup] Picture Audio Power control Setup Control Lock Input Select Position Picture Flip Language Input 2 Select ID
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 38
    operation Connect with RS-232C cross cable between the PC COM port (RS-232C connector) and the RS232C INPUT terminal on the back of monitor. "Rear view To RS-232C INPUT terminal To COM port "PC RS-232C cross cable 2 Daisy chain connection from a single PC....... Advanced operation Connect
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 39
    current value can be returned by using "?" as the parameter. Example: 1If an ID number has not been set: VOLM???? ←From PC to monitor (current volume setting: ?) 30 ←From monitor to PC (current volume setting: 30) 2If an ID number has been assigned (For example, ID number = 001) VOLM ? ←PC to
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 40
    the "Basic operation" section. You can assign a unique ID number to each monitor (see page 56). This allows you to control a particular monitor in a daisy chain of monitors. Up to about 20 monitors can be connected, depending on the length of RS-232C cables and installation environment
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 41
    using the IDST command with the Repeater control (see "Repeater control" on page 42). [Example] PC Set 1 Set 2 Set 3 Set 4 If you connect monitors as shown above, and use the command "IDST001+", ID numbers will be set automatically, as shown below. [Example] PC ID number: 1 ID number: 2 ID
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 42
    with ID number=2 to 30 ← Processing The IDLK command remains effective until it is canceled, or power is shut VOLM0020 ← Set volume of monitor with ID number=2 to 20 off. WAIT OK 002 IDLK0000 ← Canceling ID number setting WAIT ← Canceling IDLK OK 002 ← Cancelation complete VOLM0010
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 43
    returned by a specific set, assign ID numbers to each monitor in advance. If no response is returned, this may be because the monitor has not received . * If power is turned "OFF" using Repeater control, only the monitor closest to the PC returns a response. Example: (When 4 monitors are connected,
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 44
    is finished. 2Response when an ID number has been set. Space (20H) Carriage return code (0DH, 0AH) O K SPC 0 0 1 ↵ ID number of responding monitor I When a command has not been executed correctly* 1Response when no ID number has been set. Carriage return code (0DH, 0AH) ERR↵ 2Response when
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 45
    RSET, INP1, INP2, INP3, INPC, INPS, ITGD, IAVD, IPCD, CLSY, ASNC, WIDE, EMAG, EPOS, PXSL, POWR I When control via RS-232C is locked (to I MEOU T↵ I If a timeout occurs while waiting for a command (when the monitor waiting for the command is assigned an ID number = 001 in the following example
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 46
    PC Operation (Continued) If the next command is sent in the interval before OK or ERR is returned, it will basically be ignored. (Exception: Forced end using ASNC command) Leave an interval of 100 ms between command response and transmission of the next command. You can use
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 47
    except remote control and monitor button operation) after initialization 1 Electrical standby due to some error condition (See cause of last error) 2 Invalid input has continued for a long time during PC display 3 It entered standby mode (PC mode: "Mode1" in "Power Management") 4 It entered
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 48
    . Switches input to D-sub pin 15 terminal of PC Switches input to DVI terminal of PC Displays video signal from INPUT1 Displays S-terminal input video from INPUT3 Displays D-sub pin 15 terminal input video from PC Displays DVI terminal input video from PC Toggle operation Switches input to INPUT1.
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 49
    PC Operation (Continued) Picture and audio adjustment, etc. PICTURE ADJUSTMENT CONTRAST BLACK LEVEL COLOR TINT SHARPNESS RED GREEN BLUE C. M. S. (H) C. M. S. (S) C. M. S. (V) COLOR TEMP CONT WR BLVL WR COLR WR TINT WR SHRP WR REDG WR GREN WR BLUE WR CMHR WR CMHY WR CMHG
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 50
    WIDE MODE AV (Input1/Input2/Input3 WIDE WR (Component) PC (Input3 (RGB)/PC) WIDE WR PICTURE FLIP ENLARGE PFLP WR ENLARGE SETTING EMAG WR ENLARGED IMAGE POSITION EPOS WR DNR QUICK SHOOT MONITOR SPEAKER Low High Off On Fixed Variable Returns current resolution in the form xxx,xxx. V=400,
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 51
    LMNU WR REMOTE CONTROL LREM WR CONTROL BUTTONS LBTN WR POWER LPOW WR RS232C LCOM WR PIN SET PIN INPUT PIN CLEAR PIN POWER-ON METHOD, ETC. MAX VOLUME FIX VOLUME PSET W Clears the ID number if one has been designated. Sets a monitor ID number. This ID number is effective for the next and
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 52
    /COMPONENT) Adjustable range -10 - +10 Default 0 + direction For more sharpness - direction For less sharpness Advanced: C. M. S. (H) Function Adjustable range Default + direction - direction Six-color hue adjustments -30 - +30 (Red/Yellow/Green/Cyan/Blue/Magenta) 0 Move selected color hue
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 53
    interlaced signal with 2-dimensional interpolation Progressive Displays interlaced signal with 3-dimensional interpolation Note: Effective only for Video, S-video and COMPONENT 480i/576i image Red (PC (analog)/INPUT3(RGB)) Adjustable range -30 - +30 Default 0 + direction Brightens
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 54
    value) Decrease audio from the right speaker Decrease audio from the left speaker Adjusts backlight brightness -8 - +8 +8 Increases backlight brightness Decreases backlight brightness With this setting, the monitor automatically switches to (or returns from) the power standby mode, depending on the
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 55
    "Remote", "Buttons", "Power" and "RS-232C it remains canceled until the monitor enters standby mode or shuts type. INPUT1: AV / Y/C INPUT3: COMPONENT/RGB PC: Analog/Digital INPUT1: AV INPUT3: COMPONENT PC: Analog Input Signal (INPUT3 (RGB) /(PC (analog)) Function Manually selects input resolution
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 56
    Settings and Adjustments (Continued) Auto Sync.: Start Now Function Adjustable range If "Yes" is selected and the ENTER button is pressed when applicable video is input, the system automatically optimizes position, phase and clock using the video signal which is currently being input. Yes/No ("No"
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 57
    be switched when INPUT2 is currently being displayed.) ID No. Setting Function Adjustable range Default Note: Assigns ID numbers to monitors connected in a daisy chain (see page 37), using RS-232C cables. 0 - 255 0 The numbers 1 to 255 are available for ID numbers. (If "0" is set, the system
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 58
    or 576p image. Wide Mode (INPUT color system manually. Adjustable Monitor Speaker Output Function Selects whether to use built-in monitor speaker. Adjustable range On/Off Default Off On Outputs sound from built-in monitor speaker Off Does not output sound from built-in monitor speaker
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 59
    freely set by the user. The following types of operation can be locked. » Menu Display When locked, MENU buttons on the remote control and monitor are disabled. » are locked again under the following conditions. • The monitor entered standby mode. • Main POWER was turned off. • PIN was changed. •
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 60
    , and enter a 4-digit PIN. 4) After PIN input, the set locks will become effective when you close the menu. [Example: 2] Disabling remote control, monitor buttons and power operations  From the menu screen, select "Control Lock" from "Setup". 2) Go to "Lock Items", and set "Remote", "Buttons" and
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 61
    xxxx" is new PIN.) [Example: 5] Disabling remote control operation, operation using monitor buttons, and switching to the power standby state using those controls for a specific monitor (example: ID=2) in a chain of monitors connected via RS-232C. Note: Response messages are omitted for convenience
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 62
    set up 4 or 9 monitors and integrate them into a single screen to display video. Each monitor displays an enlargement of 1/4 or 1/9 of the original image. How to use the "Enlarge" feature 4 screen monitor set-up 4 monitors 1 2 3 4 1 2 3 4 9 screen monitor set-up 9 monitors 123 456 789
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 63
    Settings and Adjustments (Continued) G Wide Mode (INPUT3 (RGB) /(PC (analog)) I In PC mode, you top and bottom of the image is slightly cropped. What is "Dot by Dot"? I This function detects the resolution of the signal from a PC and displays an image with the same number of pixels, dot by dot. (
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 64
    Settings and Adjustments (Continued) G Wide Mode (Video, S-video, Input 3 COMPONENT) The desired screen size can be selected to suit the input broadcast or software. I The following 8 screen sizes can be
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 65
    . » When ordinary non-wide image (4:3) is viewed with the whole screen using the screen size switching function of this monitor, the edge of the image commercial software, parts of the image (like subtitles) image may be cropped. In this case select the optimal screen size using "Wide Mode" and
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 66
    Troubleshooting Before calling for repair services, make sure following checks for possible remedies to the encountered symptoms. Problem Check item Page There is no picture or sound. There is no picture. Remote control does not work. Right Left Sound from left and right
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 67
    standby mode if temperature continues to rise. Solution: ∫ If the monitor enters standby mode due to a rise in temperature, you can turn on the power on again in the usual way using the remote control or buttons on the monitor. However the monitor will enter standby mode again if the cause of the
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 68
    Specifications Product Model Wide LCD Monitor LC-M3700/LC-M3710 LCD Screen size inch (mm) Panel Drive Number of dots Color system Speaker Audio amplifier Terminals Power requirement Power consumption Standby power consumption Dimensions inch (mm) Weight lbs. (kg) Operating
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 69
    Appendix 1: PC Compatibility Chart ˔ PC (analog) and INPUT3 (RGB) signal input compatibility chart 43Hz (∗)
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 70
    [821.6] 1-13/32 [36] 33/64 [13] 1/4 [6.5] 22-33/64 [572] 30/64 [12] 15/16 [24] 31/64 [12.3] 33/64 [13] 1-29/64[37] 23/32 [18.5] 2-9/16 [65] 2-39/64 [66.1] 14-9/16 [370] 10-7/16 [265] 7-7/8 [200] 7-7/8 [200] 4-1/8 [105] 18-7/32 [462.8] 2-39/64 [66.1] 6-3/32 [155
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 71
    Appendix 3: Menu Option Reference Chart Menu option reference chart: PC input mode Picture Contrast Black Level Red Green Blue Advanced Reset 0 - 40 -30 - 0 - +30 -30 - 0 - + Power RS-232C Wide Mode Normal, Full, Cinema, Dot by Dot *3 DNR Off, High, Low Quick Shoot On, Off Monitor Speaker
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 72
    Picture Contrast Black Level Color Tint Sharpness Advanced Reset 0 - 40 -30 Power RS-232C Wide Mode Normal, Full 14:9, Zoom 14:9, Panorama, Cinema 14:9, Cinema 16:9, Full, Underscan Color System Auto, PAL, SECAM, NTSC3.58, NTSC4.43 DNR Off, High, Low Quick Shoot On, Off Monitor Speaker
  • Sharp LC-M3700 | LC-M3700 Operation Manual - Page 73
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
TINS-A842WJZZ
03P07-JKK
SHARP CORPORATION
Printed on 100% post-consumer recycled paper.
Gedruckt auf 100% wiederverwertungs Papier.
Imprimé sur 100% de papier recyclé.
Impreso en 100% de papel reciclado de postconsumo.
INPUT
RETURN
MENU
STANDBY/ON
ENLARGE
WIDE
LCD MONITOR
ENTER
VOL
LC-M3700
LC-M3710
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE MANEJO
WIDE LCD MONITOR
BREITBILD-LCD-MONITOR
MONITEUR GRAND ÉCRAN À
CRISTAUX LIQUIDES
MONITOR LCD PANORÁMICO
ENGLISH
DEUTSCH
FRAN
Ç
AIS
ESPA
Ñ
OL
OPERATION MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUAL DE MANEJO
LC-M3700/LC-M3710
Cover.p65
03.7.25, 1:24 PM
1