Sharp LC-M3700 LC-M3700 Operation Manual - Page 41

<Commands for ID control&gt

Get Sharp LC-M3700 PDF manuals and user guides View all Sharp LC-M3700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

PC Operation (Continued) The command examples shown on this page assume the following connection and ID number set up. PC ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST······A monitor receiving this command sets its own ID number in the parameter field. Example: IDST0001 OK 001ɹˡThe ID number of this monitor is set to 1. Note After linking monitors, you can automatically assign ID numbers by using the IDST command with the Repeater control (see "Repeater control" on page 42). [Example] PC Set 1 Set 2 Set 3 Set 4 If you connect monitors as shown above, and use the command "IDST001+", ID numbers will be set automatically, as shown below. [Example] PC ID number: 1 ID number: 2 ID number: 3 ID number: 4 IDST001+ WAIT OK 001 OK 002 OK 003 OK 004 ←ID setting command with repeater control ←ID = "OK" response from ID number=1 ←ID = "OK" response from ID number=2 ←ID = "OK" response from ID number=3 ←ID = "OK" response from ID number=4 (End) US 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
US
40
<Commands for ID control>
The command examples shown on this page assume the following connection and ID number set
up.
PC
ID number: 1
ID number: 2
ID number: 3
ID number: 4
IDST······A monitor receiving this command sets its own ID number in the parameter field.
Example:
IDST0001
OK
001
←
The ID number of this monitor is set to 1.
Note
After linking monitors, you can automatically assign ID numbers by using the IDST command with
the Repeater control (see
“
Repeater control
”
on page
42
).
PC
Set 1
Set 2
Set 3
Set 4
[Example]
If you connect monitors as shown above, and use the command
“
IDST001+
”
, ID numbers
will be set automatically, as shown below.
PC
ID number: 1
ID number: 2
ID number: 3
ID number: 4
[Example]
IDST001+
←
ID setting command with repeater control
WAIT
OK
001
←
ID =
“
OK
”
response from ID number=1
OK
002
←
ID =
“
OK
”
response from ID number=2
OK
003
←
ID =
“
OK
”
response from ID number=3
OK
004
←
ID =
“
OK
”
response from ID number=4 (End)
PC Operation (Continued)