Sony RM AV3000 Operating Instructions - Page 14

Press COMMANDER OFF., another component, repeat Steps - editable

Get Sony RM AV3000 - Universal Remote Control PDF manuals and user guides
UPC - 027242599826
View all Sony RM AV3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Setting the Code for Preset Audio and Visual Components (continued) 5 Press the four-digit component code number followed by the ENTER key on the touch-key display. Example: To enter "8056" Input "8," "0," "5," "6," and press "ENTER". If you press the CLEAR key during inputting the digits Input digits are canceled. The fourdigit component code number previously set is displayed, and the cursor returns to the first digit. When the setting of the code succeeded The selected component name, the preset four-digit component code number and "OK" light while a beep sounds. And the display returns to Step 3. 6 If you want to set a code for another component, repeat Steps 4 and 5. 7 Press COMMANDER OFF. COMMANDER OFF If you keep COMMANDER OFF pressed for more than 2 seconds The Commander turns off. If you keep COMMANDER OFF pressed for less than 2 seconds The Commander returns to the previous setting mode. Notes • If you press a component code number that is not on the table in the supplied "Component Code Numbers", the Commander beeps five times and "NG" flashes after you press the ENTER key. The setting returns to the previous one. If this happens, check the component code number, and try setting again. • If you don't input anything into the Commander for over two minutes between each step, the setup procedure will be canceled. To set the code, you must again press MUTING while pressing COMMANDER OFF. • The first digit of the component code number means the component category (TV, VCR, etc.). The component corresponding to the four-digit component code number is preset in Step 5. If you preset the component of which category is different from that preset previously to the Component Select button or the Label key, you can, if necessary, change the component names on the Mode Display key or the Label keys (see page 79). • If you preset a component code after you input character contents to the Mode Display key (page 24) or the Label keys (page 23), they are cleared and return to the original display. Edit the characters after you decide the component to be used by presetting a code. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
14
5
Press the four-digit component
code number followed by the
ENTER key on the touch-key
display.
Example: To enter
“
8056
”
Input
“
8,
”
“
0,
”
“
5,
”
“
6,
”
and press
“
ENTER
”
.
If you press the CLEAR key during
inputting the digits
Input digits are canceled. The four-
digit component code number
previously set is displayed, and the
cursor returns to the first digit.
When the setting of the code
succeeded
The selected component name, the
preset four-digit component code
number and
“
OK
”
light while a beep
sounds. And the display returns to
Step 3.
Setting the Code for Preset Audio
and Visual Components
(continued)
6
If you want to set a code for
another component, repeat Steps
4 and 5.
7
Press COMMANDER OFF.
If you keep COMMANDER OFF
pressed for more than 2 seconds
The Commander turns off.
If you keep COMMANDER OFF
pressed for less than 2 seconds
The Commander returns to the
previous setting mode.
Notes
•
If you press a component code number that is
not on the table in the supplied
“
Component
Code Numbers
”
, the Commander beeps five
times and
“
NG
”
flashes after you press the
ENTER key. The setting returns to the
previous one. If this happens, check the
component code number, and try setting
again.
•
If you don
’
t input anything into the
Commander for over two minutes between
each step, the setup procedure will be
canceled. To set the code, you must again
press MUTING while pressing
COMMANDER OFF.
•
The first digit of the component code number
means the component category (TV, VCR,
etc.). The component corresponding to the
four-digit component code number is preset
in Step 5. If you preset the component of
which category is different from that preset
previously to the Component Select button or
the Label key, you can, if necessary, change
the component names on the Mode Display
key or the Label keys (see page 79).
•
If you preset a component code after you
input character contents to the Mode Display
key (page 24) or the Label keys (page 23),
they are cleared and return to the original
display. Edit the characters after you decide
the component to be used by presetting a
code.
COMMANDER
OFF