Sony SRG300SE Installation Guide (SRG-300SE Application Guide) - Page 6

Assigning an IP address, IPv6 Setting

Get Sony SRG300SE PDF manuals and user guides View all Sony SRG300SE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Assigning an IP address To connect the device via network, you need to assign a new IP address to the device when you install it for the first time. Clicking Network after selecting a device to configure network settings with from the device list, the Network setting dialog will be displayed. This dialog is configured with two types of tabs, Basic Setting and IPv6 Setting. Basic Setting tab (when a single device is selected from the device list) Basic Setting tab (when multiple devices are selected from the device list) You can configure the network information (IPv4) of the single device selected in the device list. Device list: Displays devices for IPv4. After selecting and setting a device to configure, the device list will be updated automatically. Obtain IP address automatically: Sets DHCP mode to on. Use the following IP address: Sets the DHCP mode off. When this is set, specify the IP address, subnet mask, default gateway to specify the fixed address. You can also add a check to "After getting response of ping, the IP will be skipped" to determine whether the specified IP address is already in use or not. Obtain DNS server address automatically: Sets DNS mode to on. Use the following DNS server address: Sets DNS mode to off. When this is set, specify the preference DNS server address and alternative DNS server address. HTTP port No.: Normally, 80 should be selected. When setting a value other than 80, select the textbox and enter a port number. You can configure network information (IPv4) for multiple devices selected in the device list. Based on the selected multiple devices, the following points are different from the Basic Setting tab when a single device is selected. Use the following IP address: Sets the DHCP mode off, then specifying the start and end IP addresses enables you to configure sequential IP addresses. Network address: Displayed when multiple devices are selected from the device list and multiple network addresses exist. Selecting the network address where the device you want to configure exists enables you to configure collectively. IPv6 Setting tab (when a single device is selected from the device list) You can configure the network information (IPv6) of a single device selected in the device list. 6 Using the SNC toolbox

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Using the SNC toolbox
6
Assigning an IP address
To connect the device via network, you need to assign a
new IP address to the device when you install it for the
first time.
Clicking
Network
after selecting a device to configure
network settings with from the device list, the
Network
setting
dialog will be displayed. This dialog is
configured with two types of tabs,
Basic Setting
and
IPv6 Setting
.
Basic Setting tab (when a single device is
selected from the device list)
You can configure the network information (IPv4) of the
single device selected in the device list.
Device list:
Displays devices for IPv4. After selecting
and setting a device to configure, the device list will
be updated automatically.
Obtain IP address automatically:
Sets DHCP mode to
on.
Use the following IP address:
Sets the DHCP mode off.
When this is set, specify the IP address, subnet mask,
default gateway to specify the fixed address. You can
also add a check to “After getting response of ping,
the IP will be skipped” to determine whether the
specified IP address is already in use or not.
Obtain DNS server address automatically:
Sets DNS
mode to on.
Use the following DNS server address:
Sets DNS
mode to off. When this is set, specify the preference
DNS server address and alternative DNS server
address.
HTTP port No.:
Normally, 80 should be selected.
When setting a value other than 80, select the textbox
and enter a port number.
Basic Setting tab (when multiple devices are
selected from the device list)
You can configure network information (IPv4) for
multiple devices selected in the device list.
Based on the selected multiple devices, the following
points are different from the
Basic Setting
tab when a
single device is selected.
Use the following IP address:
Sets the DHCP mode off,
then specifying the start and end IP addresses
enables you to configure sequential IP addresses.
Network address:
Displayed when multiple devices are
selected from the device list and multiple network
addresses exist. Selecting the network address where
the device you want to configure exists enables you
to configure collectively.
IPv6 Setting tab (when a single device is
selected from the device list)
You can configure the network information (IPv6) of a
single device selected in the device list.