Yamaha Tyros2 Owner's Manual - Page 224

Removing DIMMs, Check that the installed DIMMs are functioning properly.

Page 224 highlights

Appendix Installing the Optional DIMMs 4 Insert the two DIMMs into the DIMM sockets. 168-pin DIMMs Location for DIMM installation ↑ Rear panel (Underside of the Tyros2) DIMM sockets Installing the DIMM modules to the sockets Make sure that the DIMM module is aligned correctly before you install it. Ejector lever Notch for alignment Insert the DIMM vertically in the Press it in firmly until it socket, aligning the notches to the "snaps" or locks in place. corresponding protrusions. 5 Re-install the cover you removed in step #3, in reverse order. 6 Check that the installed DIMMs are functioning properly. Set the Tyros2 right-side up, and connect the power cord to the rear-panel AC INLET jack and an AC outlet. Turn on the power and check the WAVE RAM in the PROPERTY pop-up of the Voice Creator function (page 103). If the DIMMs have been installed properly, the appropriate available memory size is indicated in the display. ■ Removing DIMMs Press the ejector lever until the DIMM unlocks. Pull the DIMM vertically out of the socket. 224 Tyros2 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240

Installing the Optional DIMMs
Appendix
224
Tyros2 Owner’s Manual
4
Insert the two DIMMs into the DIMM sockets.
5
Re-install the cover you removed in step #3, in reverse order.
6
Check that the installed DIMMs are functioning properly.
Set the Tyros2 right-side up, and connect the power cord to the rear-panel AC INLET jack and an
AC outlet. Turn on the power and check the WAVE RAM in the PROPERTY pop-up of the Voice
Creator function (page 103). If the DIMMs have been installed properly, the appropriate available
memory size is indicated in the display.
Removing DIMMs
.............................................................................................
168-pin DIMMs
Notch for alignment
Ejector
lever
Location for DIMM installation
DIMM sockets
Installing the DIMM modules to the sockets
Make sure that the DIMM module is
aligned correctly before you install it.
Insert the DIMM vertically in the
socket, aligning the notches to the
corresponding protrusions.
Press it in firmly until it
“snaps” or locks in place.
Rear panel
(Underside of the Tyros2)
Press the ejector lever
until the DIMM unlocks.
Pull the DIMM vertically
out of the socket.