ZyXEL Omni 56K USB Lite User Guide - Page 60

S-Register Descriptions, Basic S-Registers \, 3.1 Basic S-Registers ATSn=x

Get ZyXEL Omni 56K USB Lite PDF manuals and user guides View all ZyXEL Omni 56K USB Lite manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Omni 56K USB Lite RESPONSE CODE u DESCRIPTION Transmission Under run in playback state. End of stream. 5.3 S-Register Descriptions In most bit-mapped S-registers, the default bit value is 0. An asterisk follows non-0 default values. In some cases, default values are shown in the reference column preceded by +. Some bits are reserved for factory use and should not be changed. 5.3.1 Basic S-Registers "ATSn=x" Table 5-11 Basic S-Registers "ATSn=x" COMMAND S0= S1= S2= S3= S4= S5= S6= S7= S8= S9= FUNCTION AND DESCRIPTION Sets the number of rings on which the modem answers. 0 value disables auto-answer. Counts and stores number of rings from an incoming call. Defines escape code character, default '+' (43 dec.). A value of 128 to 255 disables the escape code. Defines ASCII Carriage Return. Defines ASCII Line Feed. Defines ASCII Backspace. A value of 128 to 255 disables the Backspace key's delete function. Sets the number of seconds the modem waits before dialing if 'X0' or 'X1' is selected. If a setting of 'X2,' 'X7' is selected, the modem dials as soon as it detects a dial tone. This register also sets the time-out interval for the "W" dial modifier to wait for the dial tone. (See also S41b4.) Sets duration, in number of seconds modem waits for a carrier. Sets duration, in seconds, for pause (,) option in Dial command and pause between command re-executions for Repeat (>) command. Sets duration, in tenths of a second of remote carrier signal before recognition. (Ignored if in non-FSK or half-duplex operation.) +REF. +000 +000 +043 +013 +010 +008 +003 +060 +002 +006 5-14 Command Sets

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Omni 56K USB Lite
5-14
Command Sets
RESPONSE CODE
DESCRIPTION
<DLE>u
Transmission Under run in playback state.
<DLE><ETX>
End of stream.
5.3
S-Register Descriptions
In most bit-mapped S-registers, the default bit value is 0. An asterisk follows non-0 default values. In some
cases, default values are shown in the reference column preceded by +. Some bits are reserved for factory use
and should not be changed.
5.3.1 Basic S-Registers "ATSn=x"
Table 5-11 Basic S-Registers "ATSn=x"
COMMAND
FUNCTION AND DESCRIPTION
+REF.
S0=
Sets the number of rings on which the modem answers. 0 value
disables auto-answer.
+000
S1=
Counts and stores number of rings from an incoming call.
+000
S2=
Defines escape code character, default '+' (43 dec.). A value of 128
to 255 disables the escape code.
+043
S3=
Defines ASCII Carriage Return.
+013
S4=
Defines ASCII Line Feed.
+010
S5=
Defines ASCII Backspace. A value of 128 to 255 disables the
Backspace key's delete function.
+008
S6=
Sets the number of seconds the modem waits before dialing if 'X0' or
'X1' is selected. If a setting of 'X2,' 'X7' is selected, the modem dials
as soon as it detects a dial tone. This register also sets the time-out
interval for the "W" dial modifier to wait for the dial tone. (See also
S41b4.)
+003
S7=
Sets duration, in number of seconds modem waits for a carrier.
+060
S8=
Sets duration, in seconds, for pause (,) option in Dial command and
pause between command re-executions for Repeat (>) command.
+002
S9=
Sets duration, in tenths of a second of remote carrier signal before
recognition. (Ignored if in non-FSK or half-duplex operation.)
+006