Home » ZyXEL Manuals » Networking » ZyXEL P-660HW-D1 v2 » Manual Viewer

ZyXEL P-660HW-D1 v2 User Guide - Page 87

WAN Setup, P-660HW-Dx v2 User's Guide, More Connections Edit continued

Get ZyXEL P-660HW-D1 v2 PDF manuals and user guides

View all ZyXEL P-660HW-D1 v2 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Chapter 5 WAN Setup Table 23 More Connections Edit (continued) LABEL DESCRIPTION Multiplexing Select the method of multiplexing used by your ISP from the drop-down list. Choices are VC or LLC. By prior agreement, a protocol is assigned a specific virtual circuit, for example, VC1 will carry IP. If you select VC, specify separate VPI and VCI numbers for each protocol. For LLC-based multiplexing or PPP encapsulation, one VC carries multiple protocols with protocol identifying information being contained in each packet header. In this case, only one set of VPI and VCI numbers need be specified for all protocols. VPI The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. VCI The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). Enter the VCI assigned to you. IP Address This option is available if you select Routing in the Mode field. Obtain an IP Address Automatically Select this if you get a dynamic IP address from your Internet Service Provider (ISP). A dynamic IP address is not fixed; your ISP assigns you a different one each time you connect to the Internet. This option is not available if you select RFC 1483 in the Encapsulation field. Static IP Address Select this if your ISP gave you a fixed IP address. Enter the IP address you were given in the IP Address field. IP Address If your ISP gave you an IP address to use, enter it here. Subnet Mask Enter a subnet mask in dotted decimal notation. Refer to the appendices to calculate a subnet mask If you are implementing subnetting. Gateway IP address Specify a gateway IP address (supplied by your ISP). Connection Nailed-Up Connection Select Nailed-Up Connection when you want your connection up all the time. The ZyXEL Device will try to bring up the connection automatically if it is disconnected. Connect on Demand Select Connect on Demand when you don't want the connection up all the time and specify an idle time-out in the Max Idle Timeout field. Max Idle Timeout Specify an idle time-out in the Max Idle Timeout field when you select Connect on Demand. The default setting is 0, which means the Internet session will not timeout. NAT NAT is the translation of the IP address of a host in a packet, for example, the source address of an outgoing packet, used within one network to a different IP address known within another network. None Select None to disable NAT. SUA Only SUA only is available only when you select Routing in the Mode field. Select SUA Only if you have one public IP address and want to use NAT. Click Edit to go to the Port Forwarding screen to edit a server mapping set. Back Click Back to return to the previous screen. Apply Click Apply to save the changes. Cancel Click Cancel to begin configuring this screen afresh. Advanced Setup Click this button to display the More Connections Advanced screen and edit more details of your WAN setup. P-660HW-Dx v2 User's Guide 87

Section	Page
User’s Guide	1
About This User's Guide	3
Document Conventions	4
Safety Warnings	6
Contents Overview	9
Table of Contents	11
List of Figures	21
List of Tables	27
Introduction	31
Introducing the ZyXEL Device	33
1.1 Overview	33
1.2 Ways to Manage the ZyXEL Device	35
1.3 Good Habits for Managing the ZyXEL Device	35
1.4 LEDs	35
1.5 Hardware Connections	36
1.5.1 Splitters and Microfilters	36
Introducing the Web Configurator	39
2.1 Web Configurator Overview	39
2.2 Accessing the Web Configurator	39
2.2.1 User Access	40
2.2.2 Administrator Access	40
2.3 Resetting the ZyXEL Device	42
2.3.1 Using the Reset Button	42
2.4 Navigating the Web Configurator	42
2.4.1 Navigation Panel	42
2.4.2 Status Screen	44
2.4.3 Status: Any IP Table	47
2.4.4 Status: WLAN Status	47
2.4.5 Status: Bandwidth Status	48
2.4.6 Status: Packet Statistics	48
2.4.7 Changing Login Password	50
Wizards	51
Wizard Setup for Internet Access	53
3.1 Introduction	53
3.2 Internet Access Wizard Setup	53
3.2.1 Automatic Detection	55
3.2.2 Manual Configuration	55
3.3 Wireless Connection Wizard Setup	60
3.3.1 Manually assign a WPA-PSK key	63
3.3.2 Manually assign a WEP key	63
Bandwidth Management Wizard	67
4.1 Introduction	67
4.2 Predefined Media Bandwidth Management Services	67
4.3 Bandwidth Management Wizard Setup	68
Network	73
WAN Setup	75
5.1 WAN Overview	75
5.1.1 Encapsulation	75
5.1.2 Multiplexing	76
5.1.3 Encapsulation and Multiplexing Scenarios	76
5.1.4 VPI and VCI	77
5.1.5 IP Address Assignment	77
5.1.6 Nailed-Up Connection (PPP)	77
5.1.7 NAT	78
5.2 Metric	78
5.3 Traffic Shaping	78
5.3.1 ATM Traffic Classes	79
5.4 Zero Configuration Internet Access	80
5.5 Internet Connection	80
5.5.1 Configuring Advanced Internet Connection Setup	82
5.6 Configuring More Connections	84
5.6.1 More Connections Edit	85
5.6.2 Configuring More Connections Advanced Setup	88
5.7 Traffic Redirect	89
5.8 Configuring WAN Backup	89
LAN Setup	93
6.1 LAN Overview	93
6.1.1 LANs, WANs and the ZyXEL Device	93
6.1.2 DHCP Setup	94
6.1.3 DNS Server Address	94
6.1.4 DNS Server Address Assignment	94
6.2 LAN TCP/IP	95
6.2.1 IP Address and Subnet Mask	95
6.2.2 RIP Setup	96
6.2.3 Multicast	96
6.2.4 Any IP	97
6.3 Configuring LAN IP	98
6.3.1 Configuring Advanced LAN Setup	99
6.4 DHCP Setup	100
6.5 LAN Client List	101
6.6 LAN IP Alias	102
Wireless LAN	105
7.1 Wireless Network Overview	105
7.2 Wireless Security Overview	106
7.2.1 SSID	106
7.2.2 MAC Address Filter	106
7.2.3 User Authentication	106
7.2.4 Encryption	107
7.2.5 One-Touch Intelligent Security Technology (OTIST)	108
7.3 General Wireless LAN Screen	108
7.3.1 No Security	109
7.3.2 WEP Encryption	110
7.3.3 WPA-PSK/WPA2-PSK	111
7.3.4 WPA/WPA2	113
7.3.5 Wireless LAN Advanced Setup	115
7.4 OTIST	117
7.4.1 Enabling OTIST	117
7.4.2 Starting OTIST	119
7.4.3 Notes on OTIST	120
7.5 MAC Filter	121
7.6 WMM QoS	122
7.6.1 WMM QoS Example	122
7.6.2 WMM QoS Priorities	122
7.6.3 Services	123
7.7 QoS Screen	124
7.7.1 ToS (Type of Service) and WMM QoS	125
7.7.2 Application Priority Configuration	126
Network Address Translation (NAT) Screens	129
8.1 NAT Overview	129
8.1.1 NAT Definitions	129
8.1.2 What NAT Does	130
8.1.3 How NAT Works	130
8.1.4 NAT Application	130
8.1.5 NAT Mapping Types	131
8.2 SUA (Single User Account) Versus NAT	132
8.3 SIP ALG	132
8.4 NAT General Setup	133
8.5 Port Forwarding	134
8.5.1 Default Server IP Address	134
8.5.2 Port Forwarding: Services and Port Numbers	134
8.5.3 Configuring Servers Behind Port Forwarding (Example)	135
8.6 Configuring Port Forwarding	135
8.6.1 Port Forwarding Rule Edit	136
8.7 Address Mapping	137
8.7.1 Address Mapping Rule Edit	139
Security	141
Firewalls	143
9.1 Firewall Overview	143
9.2 Types of Firewalls	143
9.2.1 Packet Filtering Firewalls	143
9.2.2 Application-level Firewalls	144
9.2.3 Stateful Inspection Firewalls	144
9.3 Introduction to ZyXEL’s Firewall	144
9.3.1 Denial of Service Attacks	145
9.4 Denial of Service	145
9.4.1 Basics	145
9.4.2 Types of DoS Attacks	146
9.5 Stateful Inspection	148
9.5.1 Stateful Inspection Process	149
9.5.2 Stateful Inspection and the ZyXEL Device	150
9.5.3 TCP Security	150
9.5.4 UDP/ICMP Security	151
9.5.5 Upper Layer Protocols	151
9.6 Guidelines for Enhancing Security with Your Firewall	152
9.6.1 Security In General	152
9.7 Packet Filtering Vs Firewall	153
9.7.1 Packet Filtering:	153
9.7.2 Firewall	153
Firewall Configuration	155
10.1 Access Methods	155
10.2 Firewall Policies Overview	155
10.3 Rule Logic Overview	156
10.3.1 Rule Checklist	156
10.3.2 Security Ramifications	156
10.3.3 Key Fields For Configuring Rules	157
10.4 Connection Direction	157
10.4.1 LAN to WAN Rules	158
10.4.2 Alerts	158
10.5 General Firewall Policy	158
10.6 Firewall Rules Summary	159
10.6.1 Configuring Firewall Rules	161
10.6.2 Customized Services	164
10.6.3 Configuring a Customized Service	164
10.7 Example Firewall Rule	165
10.8 Predefined Services	169
10.9 Anti-Probing	171
10.10 DoS Thresholds	172
10.10.1 Threshold Values	172
10.10.2 Half-Open Sessions	173
10.10.3 Configuring Firewall Thresholds	173
Content Filtering	177
11.1 Content Filtering Overview	177
11.2 Configuring Keyword Blocking	177
11.3 Configuring the Schedule	178
11.4 Configuring Trusted Computers	179
Advanced	181
Static Route	183
12.1 Static Route	183
12.2 Configuring Static Route	183
12.2.1 Static Route Edit	184
Bandwidth Management	187
13.1 Bandwidth Management Overview	187
13.2 Application-based Bandwidth Management	187
13.3 Subnet-based Bandwidth Management	187
13.4 Application and Subnet-based Bandwidth Management	188
13.5 Scheduler	188
13.5.1 Priority-based Scheduler	188
13.5.2 Fairness-based Scheduler	189
13.6 Maximize Bandwidth Usage	189
13.6.1 Reserving Bandwidth for Non-Bandwidth Class Traffic	189
13.6.2 Maximize Bandwidth Usage Example	189
13.6.3 Bandwidth Management Priorities	191
13.7 Over Allotment of Bandwidth	191
13.8 Configuring Summary	191
13.9 Bandwidth Management Rule Setup	192
13.10 DiffServ	194
13.10.1 DSCP and Per-Hop Behavior	194
13.10.2 Rule Configuration	194
13.11 Bandwidth Monitor	197
Dynamic DNS Setup	199
14.1 Dynamic DNS Overview	199
14.1.1 DYNDNS Wildcard	199
14.2 Configuring Dynamic DNS	199
Remote Management Configuration	203
15.1 Remote Management Overview	203
15.1.1 Remote Management Limitations	204
15.1.2 Remote Management and NAT	204
15.1.3 System Timeout	204
15.2 WWW	204
15.3 Telnet	205
15.4 Configuring Telnet	205
15.5 Telnet Login	206
15.6 Configuring FTP	207
15.7 SNMP	207
15.7.1 Supported MIBs	209
15.7.2 SNMP Traps	209
15.7.3 Configuring SNMP	209
15.8 Configuring DNS	210
15.9 Configuring ICMP	211
Universal Plug-and-Play (UPnP)	213
16.1 Introducing Universal Plug and Play	213
16.1.1 How do I know if I'm using UPnP?	213
16.1.2 NAT Traversal	213
16.1.3 Cautions with UPnP	213
16.2 UPnP and ZyXEL	214
16.2.1 Configuring UPnP	214
16.3 Installing UPnP in Windows Example	215
16.3.1 Installing UPnP in Windows Me	215
16.3.2 Installing UPnP in Windows XP	216
16.4 Using UPnP in Windows XP Example	217
16.4.1 Auto-discover Your UPnP-enabled Network Device	218
16.4.2 Web Configurator Easy Access	221
Maintenance and Troubleshooting	225
System	227
17.1 General Setup	227
17.1.1 General Setup and System Name	227
17.1.2 General Setup	227
17.2 Time Setting	229
Logs	233
18.1 Logs Overview	233
18.1.1 Alerts and Logs	233
18.2 Viewing the Logs	233
18.3 Configuring Log Settings	234
18.3.1 Example E-mail Log	236
18.4 Log Descriptions	237
Tools	251
19.1 Firmware Upgrade	251
19.2 Configuration Screen	253
19.2.1 Backup Configuration	253
19.2.2 Restore Configuration	254
19.2.3 Back to Factory Defaults	255
19.3 Restart	255
Diagnostic	257
20.1 General Diagnostic	257
20.2 DSL Line Diagnostic	257
Troubleshooting	259
21.1 Power, Hardware Connections, and LEDs	259
21.2 ZyXEL Device Access and Login	260
21.3 Internet Access	261
Appendices and Index	263
Product Specifications and Wall Mounting	265
Wireless LANs	271
Setting up Your Computer’s IP Address	285
IP Addresses and Subnetting	301
Firewall Commands	311
Internal SPTGEN	317
Pop-up Windows, JavaScripts and Java Permissions	333
NetBIOS Filter Commands	339
Triangle Route	341
Legal Information	343
Customer Support	347

Match case Limit results 1 per page

Chapter 5 WAN Setup

P-660HW-Dx v2 User’s Guide

Multiplexing

Select the method of multiplexing used by your ISP from the drop-down list.

Choices are

LLC

By prior agreement, a protocol is assigned a specific virtual circuit, for example,

VC1 will carry IP. If you select VC, specify separate VPI and VCI numbers for

each protocol.

For LLC-based multiplexing or PPP encapsulation, one VC carries multiple

protocols with protocol identifying information being contained in each packet

header. In this case, only one set of VPI and VCI numbers need be specified for

all protocols.

VPI

The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.

VCI

The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local

management of ATM traffic). Enter the VCI assigned to you.

IP Address

This option is available if you select

Routing

in the

Mode

field.

Obtain an IP

Address

Automatically

Select this if you get a dynamic IP address from your Internet Service Provider

(ISP). A dynamic IP address is not fixed; your ISP assigns you a different one

each time you connect to the Internet.

This option is not available if you select

RFC 1483

in the

Encapsulation

field.

Static IP Address

Select this if your ISP gave you a fixed IP address. Enter the IP address you

were given in the

IP Address

field.

IP Address

If your ISP gave you an IP address to use, enter it here.

Subnet Mask

Enter a subnet mask in dotted decimal notation.

Refer to the appendices

to calculate a subnet mask If you are implementing

subnetting.

Gateway IP address

Specify a gateway IP address (supplied by your ISP).

Connection

Nailed-Up

Connection

Select

Nailed-Up Connection

when you want your connection up all the time.

The ZyXEL Device will try to bring up the connection automatically if it is

disconnected.

Connect on

Demand

Select

Connect on Demand

when you don't want the connection up all the time

and specify an idle time-out in the

Max Idle Timeout

field.

Max Idle Timeout

Specify an idle time-out in the

Max Idle Timeout

field when you select

Connect

on Demand

. The default setting is 0, which means the Internet session will not

timeout.

NAT

NAT is the translation of the IP address of a host in a packet, for example, the

source address of an outgoing packet, used within one network to a different IP

address known within another network.

None

Select

None

to disable NAT.

SUA Only

SUA only

is available only when you select

Routing

in the

Mode

field.

Select

SUA Only

if you have one public IP address and want to use NAT. Click

Edit

to go to the

Port Forwarding

screen to edit a server mapping set.

Back

Click

Back

to return to the previous screen.

Apply

Click

Apply

to save the changes.

Cancel

Click

Cancel

to begin configuring this screen afresh.

Advanced Setup

Click this button to display the

More Connections

Advanced

screen and edit

more details of your WAN setup.

Table 23

More Connections Edit (continued)

LABEL

DESCRIPTION