ZyXEL PLA-407 User Guide - Page 32

Encrypt, - troubleshooting

Get ZyXEL PLA-407 PDF manuals and user guides View all ZyXEL PLA-407 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 4 The ENCRYPT Button 4 Press the ENCRYPT button on your second Powerline device for 1~2 seconds. The power ( ) light will blink as the PLA-407 tries to set up a connection. Figure 10 ENCRYPT Connection Procedure press for 2 seconds press for 2 seconds within 2 minutes Note: The ENCRYPT button's location varies for each Powerline device. 5 Repeat step 4 in this section for any other Powerline device you wish to connect. This must be done within 60 seconds of pressing the ENCRYPT button on the PLA-407. 6 Check the lights on the Powerline devices. The power ( ) and HomePlug ( ) lights should be blinking while the devices are connecting. Several times all lights blink simultaneously and the HomePlug ( ) light also shows red. Wait for about one minute while your Powerline devices connect. If the power ( ) light does not blink when you press ENCRYPT, you have probably pressed the ENCRYPT button for too long. Try again, pressing the ENCRYPT button for 1~ 2 seconds. If the HomePlug ( ) lights on both Powerline devices do not light up, the Powerline devices are not connected. Repeat steps 4 and 5 in this section. If that doesn't work, see the Troubleshooting in Section 9.5 on page 82 for suggestions. 32 PLA-407 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Chapter 4 The ENCRYPT Button
PLA-407 User’s Guide
32
4
Press the
ENCRYPT
button on your second Powerline device for 1~2 seconds. The
power (
) light will blink as the PLA-407 tries to set up a connection.
Figure 10
ENCRYPT Connection Procedure
Note: The
ENCRYPT
button’s location varies for each Powerline device.
5
Repeat step
4
in this section for any other Powerline device you wish to connect.
This must be done within 60 seconds of pressing the
ENCRYPT
button on the
PLA-407.
6
Check the lights on the Powerline devices. The power (
) and HomePlug (
)
lights should be blinking while the devices are connecting. Several times all lights
blink simultaneously and the HomePlug (
) light also shows red. Wait for about
one minute while your Powerline devices connect.
If the power (
) light does not blink when you press
ENCRYPT
, you have
probably pressed the
ENCRYPT
button for too long. Try again, pressing the
ENCRYPT
button for 1~ 2 seconds.
If the HomePlug (
) lights on both Powerline devices do not light up, the
Powerline devices are not connected. Repeat steps 4 and 5 in this section. If
that doesn’t work, see the Troubleshooting in Section 9.5 on page 82 for
suggestions.
within 2 minutes
press for
2 seconds
press for
2 seconds