ZyXEL PLA-407 User Guide - Page 33

Expanding the Network with ENCRYPT, 4.3 Setting Up Multiple Networks, A or B

Get ZyXEL PLA-407 PDF manuals and user guides View all ZyXEL PLA-407 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Chapter 4 The ENCRYPT Button 4.2.1 Expanding the Network with ENCRYPT If you want to add more Powerline devices to your network after the initial setup (refer to Section 4.2 on page 31), do the following. 1 To add more Powerline devices to your network, press the ENCRYPT button on device C (shown below) for more than 10 seconds until the power ( ) light flashes. 2 Then repeat steps 4 and 5 in the previous section using any Powerline device (A or B) you have connected using ENCRYPT and the Powerline device you want to connect (C). You must use the ENCRYPT button on both devices. Figure 11 Adding More Powerline Adapters to Your Network A B A or B C 3 If you have previously disconnected your computer or modem (or any other networking product connected to your Powerline device), you can now reconnect them. This sets up your Powerline network between your Powerline devices. 4.3 Setting Up Multiple Networks You can use the ENCRYPT button to set up multiple Powerline networks using your existing Powerline network. PLA-407 User's Guide 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Chapter 4 The ENCRYPT Button
PLA-407 User’s Guide
33
4.2.1
Expanding the Network with ENCRYPT
If you want to add more Powerline devices to your network after the initial setup
(refer to
Section 4.2 on page 31
), do the following.
1
To add more Powerline devices to your network, press the
ENCRYPT
button on
device
C
(shown below) for more than 10 seconds until the power (
) light
flashes.
2
Then repeat steps
4
and
5
in the previous section using any Powerline device (
A
or
B
) you have connected using
ENCRYPT
and the Powerline device you want to
connect (
C
). You must use the
ENCRYPT
button on both devices.
Figure 11
Adding More Powerline Adapters to Your Network
3
If you have previously disconnected your computer or modem (or any other
networking product connected to your Powerline device), you can now reconnect
them.
This sets up your Powerline network between your Powerline devices.
4.3
Setting Up Multiple Networks
You can use the
ENCRYPT
button to set up multiple Powerline networks using
your existing Powerline network.
A or B
A
B
C