ZyXEL PLA-407 User Guide - Page 83

The POWER lights on both devices finished blinking, but only one device's

Get ZyXEL PLA-407 PDF manuals and user guides View all ZyXEL PLA-407 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Chapter 9 LEDs and Troubleshooting • Wait for about a minute while the devices set up a connection. • If that does not work, try again with both devices connected to a power strip next to each other. If they now connect, then the devices were not on the same electrical circuit before. The POWER lights on both devices blink, then many lights blink and the HomePlug light blinks red. Do not worry, the connection process is proceeding normally. The POWER lights on both devices finished blinking, but only one device's HomePlug light is on. One device may have connected to a third Powerline device. To check device A is connected to device B and not another device, disconnect device B from its power source. Device A's HomePlug ( ) light will turn off if the connection is with Device B. Press the ENCRYPT button on both devices for more than 10 seconds, then try to reconnect, pressing the ENCRYPT button for less than 3 seconds on both devices. I pressed the ENCRYPT button for more than 10 seconds, but the HomePlug light is still on. The HomePlug light is on, indicating it is still connected to another Powerline device. Try again, pressing the ENCRYPT button for more than 10 seconds. PLA-407 User's Guide 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Chapter 9 LEDs and Troubleshooting
PLA-407 User’s Guide
83
•
Wait for about a minute while the devices set up a connection.
•
If that does not work, try again with both devices connected to a power strip
next to each other. If they now connect, then the devices were not on the same
electrical circuit before.
The POWER lights on both devices blink, then many lights blink and the
HomePlug light blinks red.
Do not worry, the connection process is proceeding normally.
The POWER lights on both devices finished blinking, but only one device’s
HomePlug light is on.
One device may have connected to a third Powerline device. To check device A is
connected to device B and not another device, disconnect device B from its power
source. Device A’s HomePlug (
) light will turn off if the connection is with
Device B. Press the
ENCRYPT
button on
both
devices for more than 10 seconds,
then try to reconnect, pressing the
ENCRYPT
button for less than 3 seconds on
both devices.
I pressed the ENCRYPT button for more than 10 seconds, but the HomePlug light
is still on.
The HomePlug light is on, indicating it is still connected to another Powerline
device. Try again, pressing the
ENCRYPT
button for more than 10 seconds.