AIWA LX-70 Operating Instructions - Page 12

02 Connecting up Connecting using the component video output You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment). • Use a component video cable (not supplied) to connect the COMPONENT VIDEO OUT jacks to a component video input on your TV, monitor or AV receiver. Be careful to match up the colours of the three jacks for correct connection. Y PB PR COMPONENT VIDEO IN TV CONTROL IN IR IN SETTING 2 SETTING 1 IR RECEIVER HDMI OUT LAN(10/100) VIDEO OUT S Y PB PR COMPONENT VIDEO OUT DIGITAL AUDIO OUT COAXIAL OPTICAL AUDIO OUT (5.1ch) CENTER SURROUND FRONT L AUDIO OUT (2ch) L R R SUB WOOFER Changing the output video resolution Use the OUTPUT RESOLUTION button located on both the front panel and the remote control to switch the output video resolution for the HDMI and component video outputs. The table below shows the output settings. Setting TV system HDMI output Component output AUTO PAL TV's preferred TV's preferred NTSC resolution *3,5 resolution *6 Video/S-Video output 576/50i 480/60i 576i or PAL 576/50i 480i NTSC 480/60i 576/50i 480/60i 576/50i 480/60i 576p or PAL 576/50p 480p NTSC 480/60p 576/50p 480/60p 576/50i 480/60i 720p PAL 720/50p NTSC 720/60p 576/50i 720/60p *1,2 576/50i 480/60i 1080i PAL 1080/50i NTSC 1080/60i 576/50i 1080/60i *1,2 576/50i 480/60i 1080p PAL 1080/50p NTSC 1080/60p 576/50i 480/60i 576/50i 480/60i Source PAL Dependent on Dependent on 576/50i Direct NTSC source *3,5 source *2,4,5 480/60i *6 For resolutions that cannot be output by component output, video is output in the following resolutions: PAL: 576/50i NTSC: 480/60i Note • Depending on your display, some of the settings may result in the picture disappearing. In this case, press OUTPUT RESOLUTION repeatedly until the picture re-appears. • 720/50p, 1080/50i, 1080/50p, 1080/60p and 1080/24p output is only compatible with HDMI displays. They are not compatible with the component video output. • When Output Video Resolution is set to 720p, 1080i or 1080p, video is output in 16:9 format even if TV Aspect Ratio is set to 4:3 (Standard). See TV Aspect Ratio on page 39. • If the contours of the displayed subjects look jagged or blurred, try setting the Output Video Resolution to 576i/480i. (If you connected this player to your TV with the HDMI connection and the picture disappears when you switch the Output Video Resolution to 576i/480i, use the component connection with the 576i/480i Output Video Resolution or S-Video, the standard composite connection instead.) • Note that when using a Component Video connection with a TV or other AV component (not using HDMI), 480/60i video may be output in 480/60p, and 576/50i video may be output in 576/50p. 24p output For smooth presentation of 1080/24p or 720/24p video with an HDMI-equipped display compatible with 1080/24p input, set 24p Direct Out on this player to On (see page 39). This player will output 1080/24p video over HDMI in the following cases: • 1080/24p video: When the Output Video Resolution is set to Auto or Source Direct. • 720/24p video: When the Output Video Resolution is set to Auto. Note • Even when 24p Direct Out is set to On, if a TV not compatible with 1080/24p video is connected, the actual frame frequency of the video output will be 60 Hz. • The video output will be interrupted when switching the video output from 1080/24p or 720/24p to other output video resolutions, or when switching to 1080/24p or 720/24p from other output video resolutions. *1 Video output is 480i during copy protected DVD-Video playback. *2 Video output during BD-ROM playback is 576i/480i depending on the disc. *3 Refer to 24p output below for conditions. *4 The frame frequency for 1080/24p is still 60 Hz. *5 The video output will be interrupted when switching the video output. 12 En