Brother International E-100 Users Manual - English - Page 53

pulling on the thread feeding out, shown at the right. Then, while

Get Brother International E-100 PDF manuals and user guides View all Brother International E-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

CONTENTS Chapter 1 Chapter 2 PULLING THE THREAD END OUT OF THE CARTRIDGE G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G 4 Use scissors to cut off the end of the thread that was pulled out. Then, insert the end of the thread into the red hole, and while twisting it, guide it through the cartridge until it comes out at the bottom of the cartridge. 1 Red hole 1 5 After the thread is fed out of the bottom of the cartridge, check that the thread is hooked over the pin shown at the right. Then, while pulling on the thread feeding out the bottom of the cartridge, close the cover. 12 1 Pin 2 Thread 3 Thread pulled out of the cartridge 3 CAUTION • If the thread is not hooked over the pin, the machine cannot embroider. 6 Trim the thread at the bottom of the cartridge so it is 3/4 to 1" (2 to 3 cm) long. 1 3/4 to 1" (2 to 3 cm) 1 WARNING Keep the needle guard cap over the needle while guiding the thread through the cartridge. If the needle sticks out, it could cause injuries. Chapter 3 Chapter 4 Chapter 5 INDEX Chapter 6 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
46
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
PULLING THE THREAD END OUT OF THE CARTRIDGE
CONTENTS
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Chapter 5
INDEX
Chapter 6
4
Use scissors to cut off the end of the
thread that was pulled out. Then, insert
the end of the thread into the red hole,
and while twisting it, guide it through
the cartridge until it comes out at the
bottom of the cartridge.
1
Red hole
5
After the thread is fed out of the
bottom of the cartridge, check that
the thread is hooked over the pin
shown at the right. Then, while
pulling on the thread feeding out
the bottom of the cartridge, close
the cover.
1
Pin
2
Thread
3
Thread pulled out of the cartridge
6
Trim the thread at the bottom of the
cartridge so it is 3/4 to 1” (2 to 3 cm) long.
1
3/4 to 1” (2 to 3 cm)
CAUTION
•
If the thread is not hooked over the pin, the machine cannot embroider.
WARNING
Keep the needle guard cap over the needle while guiding the thread through the cartridge.
If the needle sticks out, it could cause injuries.
1
3
1
2
1