Brother International FAX-1010 Service Manual - Page 60

illustrated

Get Brother International FAX-1010 PDF manuals and user guides View all Brother International FAX-1010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

(6) Remove the paper-edge sensor actuator by pulling the support "x" outwards. (7) Remove the paper ejection sensor actuator by pushing the hook "y" from the rear of the paper feed chute. Paper ejection sensor actuator ________ Latch \ Latch k_--.- z ---T7-----__ 7---1--'1'.'70 Sensor PCB Paper ejection sensor actuator \ Hook" ' \ (\-Paper ejection sensor (PH1) Paper-edge sensor (PH2) , w ,y , a _.------7 ,/ / / / , / / / Paper-edge sensor actuator -------N 7i 7 O Paper feed chute (Rear) Support "x" Separator pad Spring Paper ejection sensor (PH1) Sensor PCB Paper-edge sensor (PH2) (Rear) Main-sensor harness connector (8) Pull up the separator pad while squeezing it to the right or left. The spring also comes off. • Reassembling Notes • Make sure that the paper ejection sensor actuator is set on the sensor PCB. • As illustrated on the previous page, route the main-sensor harness through the cutout of the platen frame. When routing it through the clamp of the paper feed chute, first put the lead wires only into the clamp and then pull up the vinyl sheath.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
(6)
Remove
the
paper
-edge
sensor
actuator
by
pulling
the
support
"x"
outwards.
(7)
Remove
the
paper
ejection
sensor
actuator
by
pushing
the
hook
"y"
from
the
rear
of
the
paper
feed
chute.
Paper
ejection
sensor
actuator
(\--
k_--.
-
Paper
ejection
sensor
(PH1)
z
---
T7-----__
Latch
________
7---1--'1‘.'70
Paper
-edge
sensor
(PH2)
\
Paper
-edge
sensor
Latch
Sensor
,
actuator
PCB
w
,
y
,
a
_.
--
-
-
-
-
7
Paper
ejection
sensor
--------_______.
,/
actuator
/
--------
\
Hook"
'
\
/ /
,
/
N
7
i
/
/
7
Support
"x"
Separator
pad
O
(Rear)
Paper
feed
chute
Paper
ejection
sensor
(PH1)
Sensor
PCB
Spring
Paper
-edge
sensor
(PH2)
Main
-sensor
harness
connector
(Rear)
(8)
Pull
up
the
separator
pad
while
squeezing
it
to
the
right
or
left.
The
spring
also
comes
off.
•
Reassembling
Notes
•
Make
sure
that
the
paper
ejection
sensor
actuator
is
set
on
the
sensor
PCB.
•
As
illustrated
on
the
previous
page,
route
the
main
-sensor
harness
through
the
cutout
of
the
platen
frame.
When
routing
it
through
the
clamp
of
the
paper
feed
chute,
first
put
the
lead
wires
only
into
the
clamp
and
then
pull
up
the
vinyl
sheath.