Brother International FAX-1010 Service Manual - Page 71
Covers
 |
View all Brother International FAX-1010 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 71 highlights
1.15 Side Covers R and L (1) Lift up the front of the side cover R and take it out. (2) Disconnect the main-sensor harness from the main PCB, and then lift up the front of the side cover L and take it out together with the main-sensor harness. Platen frame Side cover L 0 GMD Hole Routing of the mainsensor harness c,N Side cover R Hole 101 ab ■ Reassembling Notes • Before putting back the side cover L, route the main-sensor harness as illustrated above. • When setting the side covers, put each rear edge under the tab and fit each hole over the boss provided on the main cover. • After installation, check the routing of the main-sensor harness, referring to Section 1.29.
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66 -
67 -
68 -
69 -
70 -
71 -
72 -
73 -
74 -
75 -
76 -
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
 |
 |
1.15
Side
Covers
R
and
L
(1)
Lift
up
the
front
of
the
side
cover
R
and
take
it
out.
(2)
Disconnect
the
main
-sensor
harness
from
the
main
PCB,
and
then
lift
up
the
front
of
the
side
cover
L
and
take
it
out
together
with
the
main
-sensor
harness.
Platen
frame
0
GMD
Side
cover
L
ab
cN
,
Hole
Routing
of
the
main
-
sensor
harness
101
Side
cover
R
Hole
■
Reassembling
Notes
•
Before
putting
back
the
side
cover
L,
route
the
main
-sensor
harness
as
illustrated
above.
•
When
setting
the
side
covers,
put
each
rear
edge
under
the
tab
and
fit
each
hole
over
the
boss
provided
on
the
main
cover.
•
After
installation,
check
the
routing
of
the
main
-sensor
harness,
referring
to
Section
1.29.