Brother International XR1300 Users Manual - English - Page 23

For models equipped with the quick-set bobbin - case

Get Brother International XR1300 PDF manuals and user guides View all Brother International XR1300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Hold the end of the thread, push the bobbin e down with your finger, and then pass the Raise the needle to its highest position by turning a the handwheel toward you (counterclockwise) or thread through the slit, as shown. press (needle position button) (for models • If the thread is not correctly inserted through equipped with the needle position button), and the tension-adjusting spring of the bobbin raise the presser foot lever. case, it may cause incorrect thread tension 1 (page 41). Turn off the sewing machine. b Slide the button and open the cover. c 1 2 1 a Tension-adjusting spring Replace the bobbin cover. Put the left tab in f place (see arrow a), and then press lightly on the right side (see arrow b) until the cover clicks into place. a Cover b Slide button Insert the bobbin with your right hand so that the d end of the thread is on the left, and then, after pulling the thread firmly around the tab with your left hand as shown, lightly pull the thread to guide it through the slit. • Replace the cover so that the end of the thread comes out from the left side of the cover (as shown by the line in the diagram). ■ For models equipped with the quick-set bobbin Memo ● The direction for feeding the bobbin thread is indicated by marks on the needle plate cover. Be sure to thread the machine as indicated. a Tab CAUTION ● Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
21
1
————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————
e
Hold the end of the thread, push the bobbin
down with your finger, and then pass the
thread through the slit, as shown.
• If the thread is not correctly inserted through
the tension-adjusting spring of the bobbin
case, it may cause incorrect thread tension
(page 41).
a
Tension-adjusting spring
f
Replace the bobbin cover. Put the left tab in
place (see arrow
a
), and then press lightly on
the right side (see arrow
b
) until the cover
clicks into place.
• Replace the cover so that the end of the
thread comes out from the left side of the
cover (as shown by the line in the diagram).
■
For models equipped with the quick-set bobbin
Memo
●
The direction for feeding the bobbin thread
is indicated by marks on the needle plate
cover. Be sure to thread the machine as
indicated.
a
Raise the needle to its highest position by turning
the handwheel toward you (counterclockwise) or
press
(needle position button) (for models
equipped with the needle position button), and
raise the presser foot lever.
b
Turn off the sewing machine.
c
Slide the button and open the cover.
a
Cover
b
Slide button
d
Insert the bobbin with your right hand so that the
end of the thread is on the left, and then, after
pulling the thread firmly around the tab with your
left hand as shown, lightly pull the thread to
guide it through the slit.
a
Tab
1
●
Make sure you set the bobbin so the thread
unrolls in the right direction. If the thread unrolls
in the wrong direction, it may cause the thread
tension to be incorrect or break the needle.
1
2
CAUTION