Brother International XR1300 Users Manual - English - Page 56

buttonhole lever, and then start sewing.

Get Brother International XR1300 PDF manuals and user guides View all Brother International XR1300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

UTILITY STITCHES Insert a pin at the end of the buttonhole k stitching to prevent the stitching from being cut, and then use a seam ripper to cut towards the pin and open the buttonhole. 2 ■ Sewing buttonholes on stretch fabrics When sewing buttonholes on stretch fabrics, use a gimp thread. Hook the gimp thread onto the part of a buttonhole foot "A" shown in the illustration so that it fits into the grooves, and then loosely tie it. 1 a Seam ripper b Pin For keyhole buttonholes, use a commercial eyelet punch to make a hole in the rounded end of the buttonhole, and then use the seam ripper to cut open the buttonhole. 1 a Eyelet punch • When using the eyelet punch, place thick paper or some other protective sheet under the fabric before punching the hole in the fabric. CAUTION ● When opening the buttonhole with the seam ripper, do not place your hands in the cutting path, otherwise injuries may result if the seam ripper slips. Do not use the seam ripper in any other way than how it is intended. Attach buttonhole foot "A". b Select a stitch or . c Adjust the stitch width to the thickness of the d gimp thread. Lower the presser foot lever and the e buttonhole lever, and then start sewing. When sewing is finished, gently pull the gimp f thread to remove any slack. Memo ● Before sewing buttonholes, check the stitch length and width by sewing a trial buttonhole on a scrap piece of fabric. Use a handsewing needle to pull the gimp g thread to the wrong side of the fabric, and then tie it. With a seam ripper, cut the middle part of the h gimp thread remaining at the top end of the buttonhole. Trim off any excess of the gimp thread. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
54
UTILITY STITCHES
—————————————————————————————————————————————————————————————————————————————————————————————————————
k
Insert a pin at the end of the buttonhole
stitching to prevent the stitching from being
cut, and then use a seam ripper to cut towards
the pin and open the buttonhole.
a
Seam ripper
b
Pin
For keyhole buttonholes, use a commercial
eyelet punch to make a hole in the rounded
end of the buttonhole, and then use the seam
ripper to cut open the buttonhole.
a
Eyelet punch
• When using the eyelet punch, place thick
paper or some other protective sheet under
the fabric before punching the hole in the
fabric.
Memo
●
Before sewing buttonholes, check the stitch
length and width by sewing a trial
buttonhole on a scrap piece of fabric.
■
Sewing buttonholes on stretch fabrics
When sewing buttonholes on stretch fabrics, use a
gimp thread.
a
Hook the gimp thread onto the part of
buttonhole foot “A” shown in the illustration
so that it fits into the grooves, and then
loosely tie it.
b
Attach buttonhole foot “A”.
c
Select a stitch
or
.
d
Adjust the stitch width to the thickness of the
gimp thread.
e
Lower the presser foot lever and the
buttonhole lever, and then start sewing.
f
When sewing is finished, gently pull the gimp
thread to remove any slack.
g
Use a handsewing needle to pull the gimp
thread to the wrong side of the fabric, and
then tie it.
h
With a seam ripper, cut the middle part of the
gimp thread remaining at the top end of the
buttonhole.
Trim off any excess of the gimp thread.
●
When opening the buttonhole with the seam
ripper, do not place your hands in the cutting
path, otherwise injuries may result if the seam
ripper slips. Do not use the seam ripper in any
other way than how it is intended.
1
2
1
CAUTION