Brother International XR1300 Users Manual - English - Page 58

slide the feed dog position lever

Get Brother International XR1300 PDF manuals and user guides View all Brother International XR1300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

UTILITY STITCHES Turn the handwheel toward you h (counterclockwise) to check that the needle correctly goes into the two holes of the button. Adjust the stitch width to the distance between the button holes. CAUTION ● When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. Start sewing. i • After sewing for about 10 seconds at low speed, press (reverse/reinforcement stitch button) to sew reinforcement stitches. Pull the upper thread at the end of the j stitching to the wrong side of the fabric, and then tie it with the bobbin thread. Use scissors to cut the upper thread and the bobbin thread at the beginning of the stitching. When you are finished attaching the button, k slide the feed dog position lever to (to the left as seen from the front of the machine) and turn the handwheel to raise the dogs. • Normally, the feed dog position lever is positioned at . 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
56
UTILITY STITCHES
—————————————————————————————————————————————————————————————————————————————————————————————————————
h
Turn the handwheel toward you
(counterclockwise) to check that the needle
correctly goes into the two holes of the
button.
Adjust the stitch width to the distance between
the button holes.
i
Start sewing.
• After sewing for about 10 seconds at low
speed, press
(reverse/reinforcement stitch
button) to sew reinforcement stitches.
j
Pull the upper thread at the end of the
stitching to the wrong side of the fabric, and
then tie it with the bobbin thread.
Use scissors to cut the upper thread and the
bobbin thread at the beginning of the stitching.
k
When you are finished attaching the button,
slide the feed dog position lever to
(to
the left as seen from the front of the machine)
and turn the handwheel to raise the dogs.
• Normally, the feed dog position lever is
positioned at
.
●
When sewing, be sure that the needle does
not touch the button, otherwise the needle
may bend or break.
CAUTION