Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 17

Feet, Place the server on its left side.

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

2-6 Removal and Replacement Procedures Feet The feet are removed for replacement, to replace the U-channel access panel, or to convert the unit from tower to rack. To remove the feet from the chassis, one at a time: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the front bezel door. See "Front Bezel Door" earlier in this chapter. 3. Place the server on its left side.  4. Remove the T-15 screw from each foot .   5. Pivot each foot down , then pull it off the base of the chassis . 3 2 1 Figure 2-3. Removing the feet from the chassis Reverse steps 1 through 5 to replace the feet. Make sure each foot snaps securely into its position.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-6
Removal and Replacement Procedures
Feet
The feet are removed for replacement, to replace the U-channel access panel, or to convert the
unit from tower to rack.
To remove the feet from the chassis, one at a time:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the front bezel door. See
“
Front Bezel Door
”
earlier in this chapter.
3.
Place the server on its left side.
4.
Remove the T-15 screw from each foot
.
5.
Pivot each foot down
, then pull it off the base of the chassis
.
1
2
3
Figure 2-3.
Removing the feet from the chassis
Reverse steps 1 through 5 to replace the feet. Make sure each foot snaps securely
into its position.