Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 18

U-Channel Access Panel, Remove the feet on the base of the U-channel access panel. See

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

2-7 U-Channel Access Panel The U-channel access panel is removed only for replacement. It does not need to be removed to access any other parts. To remove the U-channel access panel: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the front bezel door. See "Front Bezel Door" earlier in this chapter. 3. Remove the feet on the base of the U-channel access panel. See "Feet" earlier in this chapter. 4. Remove the two T-15 screws securing the U-channel access panel to the front of the chassis. 5. Pull the U-channel access panel back, then away from the chassis. Figure 2-4. Removing the U-channel access panel Reverse steps 1 through 5 to replace the U-channel access panel. Compaq ProLiant 800 Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-7
Compaq ProLiant 800 Servers Maintenance and Service Guide
U-Channel Access Panel
The U-channel access panel is removed only for replacement. It does not need to be removed to
access any other parts.
To remove the U-channel access panel:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the front bezel door. See
“
Front Bezel Door
”
earlier in this chapter.
3.
Remove the feet on the base of the U-channel access panel. See
“
Feet
”
earlier in this
chapter.
4.
Remove the two T-15 screws securing the U-channel access panel to the front of the
chassis.
5.
Pull the U-channel access panel back, then away from the chassis.
Figure 2-4.
Removing the U-channel access panel
Reverse steps 1 through 5 to replace the U-channel access panel.