Compaq ProLiant 800 ProLiant 800 Servers Supporting Pentium II Processors and - Page 35

To remove an SDRAM DIMM

Get Compaq ProLiant 800 PDF manuals and user guides View all Compaq ProLiant 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2-24 Removal and Replacement Procedures The following guidelines MUST be followed when installing or replacing memory: Use 100 MHz, 32-, 64-, 128-, or 256-MB, registered SDRAM DIMMs. WARNING: Use only Compaq SDRAM DIMMs. SDRAM DIMMs from other sources may adversely affect data integrity. Power-On Self-Test (POST) will warn of non-supported SDRAM DIMMs. To remove an SDRAM DIMM: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter.  2. Push the levers at each end of the memory module .  3. Pull the module from the board . 1 1 2 Figure 2-22. Removing a SDRAM DIMM from the system board Reverse steps 1 through 3 to replace the SDRAM DIMM. Memory modules can be installed in one way only. Match the notch on the module with the tab on the memory socket. Push the module down into the socket making sure that the module is inserted fully and seated properly.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
2-24
Removal and Replacement Procedures
The following guidelines
MUST
be followed when installing or replacing memory:
Use 100 MHz, 32-, 64-, 128-, or 256-MB, registered SDRAM DIMMs.
WARNING:
Use only Compaq SDRAM DIMMs. SDRAM DIMMs from other
sources may adversely affect data integrity. Power-On Self-Test (POST) will warn
of non-supported SDRAM DIMMs.
To remove an SDRAM DIMM:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Push the levers at each end of the memory module
.
3.
Pull the module from the board
.
1
2
1
Figure 2-22.
Removing a SDRAM DIMM from the system board
Reverse steps 1 through 3 to replace the SDRAM DIMM. Memory modules can be installed in
one way only. Match the notch on the module with the tab on the memory socket. Push the
module down into the socket making sure that the module is inserted fully and seated properly.