Dell 3330dn Mono Laser Printer User's Guide - Page 151

Streaked vertical lines, CAUTION-HOT SURFACE, Warning-Potential Damage

Get Dell 3330dn Mono Laser Printer PDF manuals and user guides View all Dell 3330dn Mono Laser Printer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 151 highlights

MAKE SURE THE PAPER PATH IS CLEAR Paper could be caught between the photoconductor kit and the fuser. Check the paper path around the fuser area. CAUTION-HOT SURFACE: The fuser and the inside of the printer near the fuser may be hot. To reduce the risk of injury from a hot component, allow the surface to cool before removing paper from this area. Clear any paper you see. THERE MAY BE EXCESS TONER IN THE PAPER PATH Contact Customer Support. Streaked vertical lines These are possible solutions. Try one or more of the following: THE TONER MAY SMEAR WHEN PAPER IS FED FROM A SPECIFIC SOURCE From Print Properties, the Print dialog, or the printer control panel, select another tray or feeder to feed paper for the job. THE TONER CARTRIDGE IS DEFECTIVE Replace the toner cartridge. MAKE SURE THE PAPER PATH IS CLEAR Paper could be caught between the photoconductor kit and the fuser. Check the paper path around the fuser area. Warning-Potential Damage: Do not touch the photoconductor on the underside of the photoconductor kit. Use the cartridge handle whenever you are holding the cartridge. CAUTION-HOT SURFACE: The fuser and the inside of the printer near the fuser may be hot. To reduce the risk of injury from a hot component, allow the surface to cool before removing paper from this area. Clear any paper you see. THERE MAY BE EXCESS TONER IN THE PAPER PATH Contact Customer Support. Troubleshooting 151

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
M
AKE
SURE
THE
PAPER
PATH
IS
CLEAR
Paper could be caught between the photoconductor kit and the fuser. Check the paper path around the fuser area.
CAUTION—HOT SURFACE:
The fuser and the inside of the printer near the fuser may be hot. To reduce the
risk of injury from a hot component, allow the surface to cool before removing paper from this area.
Clear any paper you see.
T
HERE
MAY
BE
EXCESS
TONER
IN
THE
PAPER
PATH
Contact Customer Support.
Streaked vertical lines
These are possible solutions. Try one or more of the following:
T
HE
TONER
MAY
SMEAR
WHEN
PAPER
IS
FED
FROM
A
SPECIFIC
SOURCE
From Print Properties, the Print dialog, or the printer control panel, select another tray or feeder to feed paper for
the job.
T
HE
TONER
CARTRIDGE
IS
DEFECTIVE
Replace the toner cartridge.
M
AKE
SURE
THE
PAPER
PATH
IS
CLEAR
Paper could be caught between the photoconductor kit and the fuser. Check the paper path around the fuser area.
Warning—Potential Damage:
Do not touch the photoconductor on the underside of the photoconductor kit.
Use the cartridge handle whenever you are holding the cartridge.
CAUTION—HOT SURFACE:
The fuser and the inside of the printer near the fuser may be hot. To reduce the
risk of injury from a hot component, allow the surface to cool before removing paper from this area.
Clear any paper you see.
T
HERE
MAY
BE
EXCESS
TONER
IN
THE
PAPER
PATH
Contact Customer Support.
Troubleshooting
151