Dell Alienware M16 R2 Owners Manual - Page 47

Battery cable, Removing the battery cable

Get Dell Alienware M16 R2 PDF manuals and user guides View all Dell Alienware M16 R2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Steps 1. Using the alignment posts, place the battery on the palm rest and keyboard assembly. 2. Align the screw holes on the battery with the screw holes on the palm rest and keyboard assembly. 3. Replace the four screws (M2x4) that secure the battery to the palm rest and keyboard assembly. 4. Replace the four screws (M2x4.5) that secure the battery to the palm rest and keyboard assembly. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Battery cable Removing the battery cable CAUTION: The information in this removal section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. About this task NOTE: If the battery is disconnected from the system board for service, then there is a delay during boot as the computer undergoes RTC battery reset. The following image(s) indicate the location of the battery cable and provides a visual representation of the removal procedure. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Steps
1.
Using the alignment posts, place the battery on the palm rest and keyboard assembly.
2.
Align the screw holes on the battery with the screw holes on the palm rest and keyboard assembly.
3.
Replace the four screws (M2x4) that secure the battery to the palm rest and keyboard assembly.
4.
Replace the four screws (M2x4.5) that secure the battery to the palm rest and keyboard assembly.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Battery cable
Removing the battery cable
CAUTION: The information in this removal section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
battery
.
About this task
NOTE:
If the battery is disconnected from the system board for service, then there is a delay during boot as the computer
undergoes RTC battery reset.
The following image(s) indicate the location of the battery cable and provides a visual representation of the removal procedure.
47