Dell Alienware M16 R2 Owners Manual - Page 63

Display-hinge covers, Removing the display-hinge covers

Get Dell Alienware M16 R2 PDF manuals and user guides View all Dell Alienware M16 R2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Steps 1. Using the alignment posts, place the keyboard-controller board into the slot on the palm rest and keyboard assembly. 2. Replace the screw (M2x2.5) that secures the keyboard-controller board to the palm rest and keyboard assembly. 3. Connect the keyboard-backlight cable to the connector (LEDCN1) on the keyboard-controller board and close the latch to secure the cable. 4. Connect the keyboard cable to the connector (MBCN1) on the keyboard-controller board and close the latch to secure the cable. 5. Connect the keyboard-controller board cable to the system board and close the latch to secure the cable. Next steps 1. Install the battery. 2. Install the base cover. 3. Follow the procedure in After working inside your computer. Display-hinge covers Removing the display-hinge covers CAUTION: The information in this removal section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the rear I/O cover. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Steps
1.
Using the alignment posts, place the keyboard-controller board into the slot on the palm rest and keyboard assembly.
2.
Replace the screw (M2x2.5) that secures the keyboard-controller board to the palm rest and keyboard assembly.
3.
Connect the keyboard-backlight cable to the connector (LEDCN1) on the keyboard-controller board and close the latch to
secure the cable.
4.
Connect the keyboard cable to the connector (MBCN1) on the keyboard-controller board and close the latch to secure the
cable.
5.
Connect the keyboard-controller board cable to the system board and close the latch to secure the cable.
Next steps
1.
Install the
battery
.
2.
Install the
base cover
.
3.
Follow the procedure in
After working inside your computer
.
Display-hinge covers
Removing the display-hinge covers
CAUTION: The information in this removal section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
rear I/O cover
.
63