Dell Alienware M16 R2 Owners Manual - Page 56

Power-adapter port, Removing the power-adapter port

Get Dell Alienware M16 R2 PDF manuals and user guides View all Dell Alienware M16 R2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Steps 1. Using the alignment posts, place the left and right speakers into their slots on the palm rest and keyboard assembly. NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker. 2. Route the speaker cable through the routing guides on the palm rest and keyboard assembly. 3. Adhere the tapes that secure the speaker cable to the palm rest and keyboard assembly. 4. Connect the speaker cable to connector (SPK1) on the audio board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Power-adapter port Removing the power-adapter port CAUTION: The information in this removal section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the rear I/O cover. 4. Remove the fan and heat-sink assembly. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Steps
1.
Using the alignment posts, place the left and right speakers into their slots on the palm rest and keyboard assembly.
NOTE:
Ensure that the alignment posts are threaded through the rubber grommets on the speaker.
2.
Route the speaker cable through the routing guides on the palm rest and keyboard assembly.
3.
Adhere the tapes that secure the speaker cable to the palm rest and keyboard assembly.
4.
Connect the speaker cable to connector (SPK1) on the audio board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Power-adapter port
Removing the power-adapter port
CAUTION: The information in this removal section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
rear I/O cover
.
4.
Remove the
fan and heat-sink assembly
.
56