Dell Alienware m15 R2 Service Manual - Page 37

System board, Removing the system board

Get Dell Alienware m15 R2 PDF manuals and user guides View all Dell Alienware m15 R2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Steps 1. Using the alignment posts, place the left speaker on the palm-rest assembly. NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker. 2. Route the speaker cable through the routing guides on the palm-rest assembly. 3. Using the alignment posts, place the right speaker on the palm-rest assembly. NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker. 4. Connect the speaker cable to the right I/O-board. Next steps 1. Install the battery. 2. Install the 2230 solid-state drive. (if applicable) 3. Install the 2280 solid-state drive. (if applicable) 4. Install the base cover. 5. Follow the procedure in After working inside your computer. System board Removing the system board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the 2230 solid-state drive. (if applicable) 4. Remove the 2280 solid-state drive. (if applicable) 5. Remove the rear I/O-cover. 6. Remove the battery. 7. Remove the right I/O-board. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Steps
1.
Using the alignment posts, place the left speaker on the palm-rest assembly.
NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker.
2.
Route the speaker cable through the routing guides on the palm-rest assembly.
3.
Using the alignment posts, place the right speaker on the palm-rest assembly.
NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker.
4.
Connect the speaker cable to the right I/O-board.
Next steps
1.
Install the
battery
.
2.
Install the
2230 solid-state drive
. (if applicable)
3.
Install the
2280 solid-state drive
. (if applicable)
4.
Install the
base cover
.
5.
Follow the procedure in
After working inside your computer
.
System board
Removing the system board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
2230 solid-state drive
. (if applicable)
4.
Remove the
2280 solid-state drive
. (if applicable)
5.
Remove the
rear I/O-cover
.
6.
Remove the
battery
.
7.
Remove the
right I/O-board
.
37