Epson EPL-N1200 User Manual - Page 102

the error message still appears, turn off the printer, unplug

Get Epson EPL-N1200 PDF manuals and user guides View all Epson EPL-N1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Reset All All printer settings for all interfaces have been reset to the default configuration. Reset to Save You have changed a SelecType setting but the new value is not activated yet. Do one of the following: (1) exit SelecType by pressing Continue or On Line (the new setting is activated after the current print job is finished), or (2) reset the printer by pressing ALT and Reset at the same time. Self Test The printer is performing its internal self test; wait a few moments for it to finish. Service Req.Cnnn Service Req.Ennn A controller error (Cnnn) or a print engine error (Ennn) has occurred. Write down the error number and turn off the printer. Wait at least five seconds and then turn it back on. If the error message still appears, turn off the printer, unplug the power cord, and contact an authorized EPSON Customer Care Center. Standby The printer is in its low power state. If the On Line light is on, it is still on line and you may send a print job. Toner Low The printer is almost out of toner. You should replace the imaging cartridge soon; see Chapter 5 for instructions. 6-6 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Reset All
All printer settings for all interfaces have been reset to the
default configuration.
Reset to Save
You have changed a SelecType setting but the new value is not
activated yet. Do one of the following: (1) exit SelecType by
pressing
Continue
or
On Line
(the new setting is activated
after the current print job is finished), or (2) reset the printer by
pressing
ALT
and
Reset
at the same time.
Self Test
The printer is performing its internal self test; wait a few
moments for it to finish.
Service Req.C
nnn
Service Req.E
nnn
A controller error (
C
nnn
) or a print engine error (
E
nnn
) has
occurred. Write down the error number and turn off the
printer. Wait at least five seconds and then turn it back on. If
the error message still appears, turn off the printer, unplug the
power cord, and contact an authorized EPSON Customer Care
Center.
Standby
The printer is in its low power state. If the
On Line
light is on, it
is still on line and you may send a print job.
Toner Low
The printer is almost out of toner. You should replace the
imaging cartridge soon; see Chapter 5 for instructions.
6-6
Troubleshooting