Epson EPL-N1200 User Manual - Page 107

The display panel stays blank after you turn on the printer., The printer doesn't print and

Get Epson EPL-N1200 PDF manuals and user guides View all Epson EPL-N1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

The display panel stays blank after you turn on the printer. Turn off the printer and check the power cable connections between the printer and the electrical outlet; then turn the printer back on. If the electrical outlet is controlled by an outside source such as a wall switch, plug the printer into a different outlet. Also plug another electrical device into the outlet to check whether the outlet is operating properly. The printer doesn't print and the On Line light is off. Press On Line once; the On Line light should come on. The On Line light is on but nothing prints. Your computer may not be properly connected to the printer. Check both ends of the cable between your printer and computer. Also make sure your interface cable meets the specifications for your printer and computer. If you are using the serial interface, set the baud rate, protocol, data bit, and related settings. See your computer manual for the correct settings and interface requirements. If you are using a parallel interface, check the Speed setting in SelecType to match the value the computer requires; see Chapter 3 for details. Make sure that your software is properly set up for your printer. The imaging cartridge may be empty; if necessary, replace it as described in Chapter 5. Troubleshooting 6-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
The display panel stays blank after you turn on the printer.
Turn off the printer and check the power cable connections
between the printer and the electrical outlet; then turn the
printer back on.
If the electrical outlet is controlled by an outside source such as
a wall switch, plug the printer into a different outlet. Also plug
another electrical device into the outlet to check whether the
outlet is operating properly.
The printer doesn’t print and the
On Line
light is off.
Press
On Line
once; the
On Line
light should come on.
The
On Line
light is on but nothing prints.
Your computer may not be properly connected to the printer.
Check both ends of the cable between your printer and
computer. Also make sure your interface cable meets the
specifications for your printer and computer.
If you are using the serial interface, set the baud rate, protocol,
data bit, and related settings. See your computer manual for
the correct settings and interface requirements.
If you are using a parallel interface, check the
Speed
setting in
SelecType to match the value the computer requires; see
Chapter 3 for details.
Make sure that your software is properly set up for your
printer.
The imaging cartridge may be empty; if necessary, replace it as
described in Chapter 5.
Troubleshooting
6-11