Epson EX-1000 User Manual - Page 34

Installing the Paper Guide, installed horizontally

Get Epson EX-1000 - Impact Printer PDF manuals and user guides View all Epson EX-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

10. If the paper is straight and has no wrinkles, lock the right sprocket unit in place. 11. Turn the paper feed knob slowly to feed the paper under the metal plate in front of the tractor. (The diagram on the metal plate shows how the paper should go through.) See that the paper does not wrinkle after it reaches the platen. 12. Turn the knob until the paper is past the paper bail. Then push back the paper bail lever (the lever on the right side). The paper bail lever must be back at all times when you are printing with continuous paper. Installing the Paper Guide Install the paper guide to prevent the outgoing paper from being pulled back into the printer. This is the same part that supports the paper when you print on single sheets, but with continuous paper, it is installed horizontally The paper guide has notches at either side that fit over two pins located at the sides of the tractor. 1. Hold the guide above the printer, with the curved end down. 2. Lower the notches onto the pins as shown below, then tilt the paper guide back until it lies horizontally over the paper. Figure 2-5. Installing the paper guide Choosing and Loading Paper 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
10. If the paper is straight and has no wrinkles, lock the right sprocket
unit in place.
11. Turn the paper feed knob slowly to feed the paper under the metal
plate in front of the tractor. (The diagram on the metal plate shows
how the paper should go through.) See that the paper does not
wrinkle after it reaches the platen.
12. Turn the knob until the paper is past the paper bail. Then push
back the paper bail lever (the lever on the right side). The paper
bail lever must be back at all times when you are printing with
continuous paper.
Installing the Paper Guide
Install the paper guide to prevent the outgoing paper from being
pulled back into the printer. This is the same part that supports the
paper when you print on single sheets, but with continuous paper, it is
installed horizontally
The paper guide has notches at either side that fit over two pins
located at the sides of the tractor.
1. Hold the guide above the printer, with the curved end down.
2. Lower the notches onto the pins as shown below, then tilt the paper
guide back until it lies horizontally over the paper.
Figure 2-5.
Installing the paper guide
Choosing and Loading Paper
2-5