Gateway E-9525R Gateway E-9525R Server User Guide - Page 41

Removing and installing a tape drive, Caution

Get Gateway E-9525R PDF manuals and user guides View all Gateway E-9525R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

www.gateway.com 14 Secure the assembly by tightening the thumbscrew you previously loosened. 15 Attach the 44-pin optical drive cable to the back of the optical drive interface board. 16 Reinstall the large fan cage by following the instructions in "Replacing system fans" on page 44. 17 Follow the instructions in "Closing the server case" on page 32. 18 Reinstall the bezel, if required, by snapping it into place on the front of the chassis. 19 Reconnect all power cords and peripheral device cables, then turn on the server. Removing and installing a tape drive To remove and install a tape drive: Caution The tape drive is not hot-swappable. Before installing or removing the drive, make sure that power is turned off and the power cord(s) is unplugged. 1 Follow the instructions in "Preventing static electricity discharge" on page 30. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server. 2 Unlock the bezel (if necessary) and remove it by pulling it from the chassis. 3 Follow the instructions in "Opening the server case" on page 31. 4 Remove the large fan cage by following the instructions in "Replacing system fans" on page 44. 5 Disconnect the data and power cables from the tape drive. 6 Loosen the thumbscrew (1) holding the media cage in the chassis, then push the assembly (2) out the front of the chassis. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
www.gateway.com
35
14
Secure the assembly by tightening the thumbscrew you previously loosened.
15
Attach the 44-pin optical drive cable to the back of the optical drive interface board.
16
Reinstall the large fan cage by following the instructions in
“Replacing system fans” on
page 44
.
17
Follow the instructions in
“Closing the server case” on page 32
.
18
Reinstall the bezel, if required, by snapping it into place on the front of the chassis.
19
Reconnect all power cords and peripheral device cables, then turn on the server.
Removing and installing a tape drive
To remove and install a tape drive:
1
Follow the instructions in
“Preventing static electricity discharge” on page 30
. Make sure
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
2
Unlock the bezel (if necessary) and remove it by pulling it from the chassis.
3
Follow the instructions in
“Opening the server case” on page 31
.
4
Remove the large fan cage by following the instructions in
“Replacing system fans” on
page 44
.
5
Disconnect the data and power cables from the tape drive.
6
Loosen the thumbscrew (1) holding the media cage in the chassis, then push the
assembly (2) out the front of the chassis.
Caution
The tape drive is not hot-swappable. Before installing or removing the drive,
make sure that power is turned off and the power cord(s) is unplugged.