Gateway E-9525R Gateway E-9525R Server User Guide - Page 59

Installing and removing the ROMB battery pack for the mezzanine RAID card

Get Gateway E-9525R PDF manuals and user guides View all Gateway E-9525R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

www.gateway.com 11 Slide the backplane to the right, locking it into place on the backplane bracket. 12 Insert the backplane bracket and backplane into the chassis (3) between the two rows of button-shaped fixtures on the bottom of the chassis. 13 Reconnect all cables to the backplane. 14 Replace the system fans and fan duct by following the instructions in "Replacing system fans" on page 44. 15 Follow the instructions in "Closing the server case" on page 32. 16 Reinstall the hot-swap drives back into the server. Make sure that you install the drives into the same bays you removed them from in Step 4. For instructions see "Removing and installing a hard drive" on page 37. 17 Replace the bezel by snapping it into place on the front of the server. Installing and removing the ROMB battery pack for the mezzanine RAID card To remove and install a ROMB battery pack for the mezzanine RAID card: 1 Follow the instructions in "Preventing static electricity discharge" on page 30. Make sure that you turn off the server, then unplug the power cord(s) and all other cables connected to the server. 2 Follow the instructions in "Opening the server case" on page 31. 3 Push the release lever (1), then lift the ROMB battery pack for the mezzanine RAID card (2) out of the chassis. 4 Align the new battery with the battery slot, then push the new battery into the slot until it clicks into place. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
www.gateway.com
53
11
Slide the backplane to the right, locking it into place on the backplane bracket.
12
Insert the backplane bracket and backplane into the chassis (3) between the two rows of
button-shaped fixtures on the bottom of the chassis.
13
Reconnect all cables to the backplane.
14
Replace the system fans and fan duct by following the instructions in
“Replacing system
fans” on page 44.
15
Follow the instructions in
“Closing the server case” on page 32
.
16
Reinstall the hot-swap drives back into the server. Make sure that you install the drives into
the same bays you removed them from in
Step 4
. For instructions see
“Removing and
installing a hard drive” on page 37
.
17
Replace the bezel by snapping it into place on the front of the server.
Installing and removing the ROMB battery pack
for the mezzanine RAID card
To remove and install a ROMB battery pack for the mezzanine RAID card:
1
Follow the instructions in
“Preventing static electricity discharge” on page 30
. Make sure
that you turn off the server, then unplug the power cord(s) and all other cables connected
to the server.
2
Follow the instructions in
“Opening the server case” on page 31
.
3
Push the release lever (1), then lift the ROMB battery pack for the mezzanine RAID card (2)
out of the chassis.
4
Align the new battery with the battery slot, then push the new battery into the slot until
it clicks into place.