Gateway E-9525R Gateway E-9525R Server User Guide - Page 63

Place the old system board in a static-free bag for storage., standoffs 2

Get Gateway E-9525R PDF manuals and user guides View all Gateway E-9525R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

www.gateway.com 4 Remove the fan duct and system fan cage by following the instructions in "Replacing system fans" on page 44. 5 Remove the memory modules by following the instructions in "Installing memory" on page 39. 6 Remove the heatsinks and processors by following the instructions in "Replacing or adding a processor" on page 47. 7 Disconnect all cables from the system board, noting their locations and orientation. (You will reconnect the cables after you install the new board.) 8 Loosen the two thumbscrews (1) that secure the system board to the server. 2 2 2 2 2 1 2 2 9 Slide the system board toward the back of the server until it is free of the eight retaining standoffs (2), then lift the board from the chassis. 10 Place the old system board in a static-free bag for storage. 11 Insert the new system board into the chassis, aligned with the eight retaining standoffs, then slide the board toward the front of the case so the board is held by the standoffs. 12 Tighten the two system board thumbscrews to secure the board into the chassis. 13 Connect the cables you removed in Step 7. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
www.gateway.com
57
4
Remove the fan duct and system fan cage by following the instructions in
“Replacing system
fans” on page 44
.
5
Remove the memory modules by following the instructions in
“Installing memory” on
page 39
.
6
Remove the heatsinks and processors by following the instructions in
“Replacing or adding
a processor” on page 47
.
7
Disconnect all cables from the system board, noting their locations and orientation. (You
will reconnect the cables after you install the new board.)
8
Loosen the two thumbscrews (1) that secure the system board to the server.
9
Slide the system board toward the back of the server until it is free of the eight retaining
standoffs (2), then lift the board from the chassis.
10
Place the old system board in a static-free bag for storage.
11
Insert the new system board into the chassis, aligned with the eight retaining standoffs,
then slide the board toward the front of the case so the board is held by the standoffs.
12
Tighten the two system board thumbscrews to secure the board into the chassis.
13
Connect the cables you removed in
Step 7.
2
2
2
2
2
1
2
2